Question about 1989 Ford Ranger

1 Answer

I have an 88 ford 350 and lost the key and it is stuck in off position i am trying to change it but dont know how

Posted by on

  • yadayada
    yadayada May 19, 2011

    Without the key you must drill the lock guts out.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,252 Answers

First remove the negative battery cable.
It has to be in the LOCK position...
remove the steering wheel.
on tilt wheel applications, remove the upper extension shroud by squeezing it at the top and bottom positions and popping it free of the retaining plate at the right.
remove the 2 trim shroud halves.
disconnect the ignition switch electrical connector.
drill out the break off head bolts connecting the switch to the lock cylinder housing by using a
1/8 in. drill, and remove both bolts.
disengage the ignition switch from the actuator pin.

Posted on May 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Truck want start fills like there's air in the line.


1988 F350 NO CRANK NO START - YouTube

? 8:10
https://www.youtube.com/watch?v=SRKTLUJGK0A
May 3, 2013 - Uploaded by DUSTINSMOBILE WRENCH
... a New Ford F-350 Truck on a Trailer - Duration: 0:31. by Belt Liner 2,323,434 views. 0:31. 92-2014 Ford F-150 250 350 Expedition won't start ...

1986 Ford F350 won't start - YouTube

? 1:01
https://www.youtube.com/watch?v=ADUc1UHVhkM
Oct 13, 2013 - Uploaded by Tristen Perry
Hello people on YouTube. I have a 86 F350 that won't start up. It has a brand new solenoid in it. The truck ...

88 F-350 with EFI 460 Starting/Running Problems - Ford F ...

fordfzone.com > Technical Support > 80-96 Ford Truck Tech Support

Jan 26, 2007 - 11 posts - ‎8 authors
Will not re-start, seems to be flooding at this point. ... I have a 1988 Ford F-350 with an EFI 460 engine. ... run a couple of seconds, shut off if you didn't start the truck. they now run all the time when the key is in the on position.

Jan 05, 2016 | 1988 Ford F 350

1 Answer

Ive lost my key to my 2000 ford taurus my door has a num pad on it how do i reset it


Have to see the dealer & also have an owners manual
to change the codes to what you want on the door

Ignition keys you lost?

You should have at least three keys programmed to
the ignition key detector system (First)

Aug 01, 2014 | 2000 Ford Taurus

1 Answer

My 1979 ford f 350 will not start. When the key is turned I can here a single click, The battery is fully chrged and a new starter has been installed. Afterwards I still got a single click when the key was...


It's the solenoid....Follow the positive cable from the battery too...it is connected to the solenoid.
there will be 3 maybe 4 wires...two bolted one or two push on....change this and you should be good to go...

Jul 06, 2011 | 1979 Ford F 350

1 Answer

How do I change the ignition switch in a 1995 F-350? The original key was lost.


*If* you had the key these are the steps: Insert the key and turn to the RUN position. There is a small hole in the steering column below the ignition switch. Insert a 1/8" drill bit (or something similar size) and push upward on the retaining pin in the hole. As you do this, pull out the cylinder lock. It should come right out. To reinstall, turn the new cylinder to the RUN position. Again depress the retaining pin and insert the switch into the steering column. Make sure the new switch is completely seated & aligned before you turn to the OFF position. This will let the retaining pin extend into the hole.

Because you do not have the key you will need to pick (or have the lock picked) before you can replace the lock cylinder.

Sep 12, 2010 | 1995 Ford F350

1 Answer

88 camaro


It could be a relay that keeps the fuel pump running when the ignition switch is in the run position. My jeep had this problem, where the pump gets power in the start position but once the key returns to run, the engine shortly stops running because the pressure in the fuel line drops off as it is used by the running engine, it usually died within 3 seconds. my relay was under hood and there were several of the same type in there, I switched the fuel system one with the one for my AC(which only blows hot anyway) Hope this helps...

Feb 24, 2010 | 1988 Chevrolet Camaro

1 Answer

I have a 1988 f-350 diesel and i have lost my key and bought it without a spare how do i remove the ingnition with out a key


You don't without ruining it. I suggest you get a locksmith to make you a new key they can get in there somehow and make a key. In 1988 did Ford use a seperate key for doors? If the doors are the same or the glove box those locks are easier to remove. Also, I've never tried this with a Ford but on newer GM cars if you take the title to a dealer they can make a key from the (VIN) serial number. But, you have to have the title to prove ownership of the vehicle. I don't know if they can do that on an 88 or not. Good luck.

Feb 09, 2010 | 1988 Ford F 350

1 Answer

1996 ford f 350 rear right power window wont roll back up we rolled it all the way down now its stuck down


Try tapping lightly on the door panel in different places,while the key is on,and holding the window switch in the up position.sometimes,that will jar the motor and the window will work.

Oct 03, 2009 | 1996 Ford F350 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...