Question about 2002 Hyundai Accent

1 Answer

Starts,idles & runs fine, but won't rev over 2400

Posted by on

  • 2 more comments 
  • William Elliott
    William Elliott May 25, 2011

    Hi ! I replaced the MAP senser. This caused no change in RPM's. Please take another look at my problem. Many Thanks, Bill

  • William Elliott
    William Elliott May 26, 2011

    Dear Fixya Expert - I replaced the MAP sensor, and all wiring seems good. the motors RPM's are unchanged. Please take another look at my problem. Thanks Bill

  • William Elliott
    William Elliott May 26, 2011

    Dear Fixya I replaced the MAP sensor & checked wires--It still will not rev over 2400 RPM's.Please advise. Thanks Bill

  • William Elliott
    William Elliott May 27, 2011

    I am about to give up trying to contact you. The fix did not work. Please advise. William Elliott Phone 863-875-2992 Nickname landsail.elliott@gmail.com Temp password d31c2

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 5,370 Answers

This is indication of faulty MAF sensor. Its located on the air inlet, look and the air filter box and follow it to the engine there inline you will see the mass air flow sensor and the air intake temp sensor is built into the mass air flow sensor. when you locate the air filter box you will see the maf sensor its bolted to air box.Make sure the connector is good and also the wiring.Remove the MAF sensor, clean it and recheck.Also try driving without MAF sensor.If its revs fine, then its faulty MAF.------- This should help.Thanks.Helpmech.

Posted on May 19, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pathfinder "cuts out" at 2,300 rpm


Replace your MAF, its a little pricey around $280.00 or so but this will clear the code but make sure you have the ECM reprogrammed to perform a "learning" sequence since sometimes the code will not clear even though the vehicle will run like new. This reprogramming will most likely have to be a dealer performed procedure.

May 02, 2013 | 2003 Nissan Pathfinder

1 Answer

Santa fe idles but will not rev above 2000 rpm's - won't take a load


make sure you have the wires in the right places. (see pic)
Make sure you did not leave something unplugged. (sensor/vacuum line)
12_22_2012_10_22_13_pm.jpg

Dec 22, 2012 | Cars & Trucks

1 Answer

Engine starts and idles fine, but will not rev up (2001 Jeep Grand Cherokee 3.1 diesel auto)


If it was a fuel shortage the engine would rev but to limited speed. This is a lack of air to throttle body. Check for clogged air filter and all the piping and the throttle body.

Sep 28, 2012 | 2001 Jeep Grand Cherokee

1 Answer

My rpm rev's past 3 car stalls then shifts...sometimes won't shift


Due for a transaxle rebuild,common on that veh

The fact you continued to drive it when it won't
shift correctly & has been slipping, your done

Aug 30, 2012 | 1998 Plymouth Grand Voyager

1 Answer

A wet air filter was put into my nissan sentra gxe with a 1.8L engine. It will start and idle, but won't rev much past 2000 rpm's. The filter was rmoved and the car sat in the sun all day hopi


never wash or wet an air filter as it closes up the pores in the paper element
fit a new element and then run the fault codes or reset the ECM using a scan tool

Jan 19, 2018 | 2003 Nissan Sentra

1 Answer

95 nissan truck won't rev and runs rough


sounds like it's running in closed loop. O2 sensor, MAP sensor, or MAF sensor...sensor issues

May 18, 2012 | 1995 Nissan Pickup

2 Answers

I have a 1993 300zx twin turbo that's heavily


you are SURE you have enough fuel pressure? like 60?

Feb 19, 2012 | 1993 Nissan 300ZX

1 Answer

1993 nissan


Can you not get any RPM out of it above idle, or does it rev to a certain point (say, 2400 RPM) and then refuse to go higher? If it's the latter, where the revs stop at a certain low point, check the mass airflow sensor out - on my 300ZX, a bad mass airflow sensor triggered the computer to limit RPM to 2400 to keep from damaging anything in the engine.

Oct 20, 2008 | 1993 Nissan Pathfinder

Not finding what you are looking for?
2002 Hyundai Accent Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...