Question about Hyundai Genesis Coupe

1 Answer

What do you call the plastic trim under the front wheel arch behind the front bumper of a hyundai coupe s111 2007

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

If you drop by a hyundai dealer they have a parts guy who will be happy to show you an illustrated parts breakdown on the car. then you will know the part name, part number, dealer cost, and time to install.

alternatively you can look on eBay for someone selling an IPB on CD for a few bucks.

Posted on May 19, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing front bumper


there will be bolts behind the bumper , to gain access remove the inner wheel arch linings and look under front of vehicle as should be able to see the bolts there as well ,may have an under tray to remove to gain access there as well

Jun 07, 2014 | 1997 Geo Tracker 2 Door

1 Answer

Removing jaguar s type rear bumper..


disconnect the connector from the park aid module push the connector and grommet out of the back panel remove screws from lower rear of wheel arch liners remove boot floor trim remove plastic boot closing panel trim remove both boot side trims you wil find a number of 10mm headed bolts around the boot at the sides and back remove these and get someone to help you remove the bumper liner the 2 outer sensors can normally be changed without removing the bumper liner on some models

Mar 26, 2013 | 2003 Jaguar S-Type

1 Answer

How to remove a bumper on a peugeot 308


I have just finished replacing the broken grille on my wife's Peugeot 308 (09 reg) wiuth the help of a YouTube video in Russian .... http://www.youtube.com/watch?v=3-KxbwKnvJE ...not that I could understand what they were saying but at least you can follow what they are doing.

If attempting this, allow a good three hours which is what it took me as there are many bolts to undo and a knack of pushing and pulling fragile plastic lugs. Take your time.

Removal can be done without putting car on ramps as you will need to put the wheels on full lock to get at the wheel-arch liners.

Firstly, undo the various screws on the plastic tray underneath the engine which connect to the front bumper skirt. There are three main bolts with washers which are located half way back, one central and one each side.

Secondly, put the steering on full lock to give you access to the wheel-arch liner for each front wheel. Pull the wheel-arch liner back to reveal a 10mm bolt where the bumper meets the wing of the car. You will need a ratchet with a swivel knuckle and 10mm socket to get onto the bolt head. Undo the bolt and repeat on the other side.

Lift the bonnet and at the front edge you will see four black flat circles. Using a small flat blade screwdriver, lever up the centre and you can then lift up with your finger which releases the retaining plastic bolts.

Looking at the top of the panted front bumper where it attached to the front of the engine compartment, you will see several small slots along the width of the plastic which you can place a small flat bladed screwdriver into and push down gently whilst pulling the front panel forwards in a rocking motion to release the plastic lugs. The whole bumper assembly should then start disconnecting from the car. It is helpful to have a second person to gentle prise away the wheel-arch sections from the car body. The whole front bumper section should then fall away but be careful as the wiring for the front fog lights will still be attached. Take hold of the lamp holders and turn through 90 degrees to remove the bayonet fittings. Pull the bumper assembly clear of the car and place on a fabric cloth/mat to avoid scratching the paintwork.

Re-fitting is a reverse of the above.

Feb 23, 2012 | Cars & Trucks

2 Answers

Hi I have a mazda mx5 mk3 from the UK and I am looking to change my headlights in order for me to register my car in France. I need to change the full headlight assembly and was wondering if you could...


try fitting stick on beam correctors on the outside of the headlamps you usally buy them from a mazda dealers parts dept a lot cheaper than fitting headlamps and comply with french and uk law once fitted

Feb 24, 2011 | Mazda MX-5 Miata Cars & Trucks

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?


take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.
  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Dec 27, 2010 | 2005 Hyundai Tucson

1 Answer

How do i get to the washer reservoir, its leaking. Do i need to take the front bumper off (if so how?) or can i get to it via the wheel arch liner?


you have to take your left front wheel off,then remover the plastic inner guard,the washer reservoir is behind it by the front bumper.

May 20, 2010 | 1993 Honda Prelude

1 Answer

Jaguar x type 2004 front bumper


Front bumper removal is quite easy. To start with there is 4 10mm bolts one by each headlamp ( with the bonnet open) remov them. There is 3 T30 screws that hold the under tray to the subframe and there is also a small corner trim that is on the bumper side of the front wheel arch here is 3 T30 screws holding them on on each side. Finally remove the front wheel arch lining so you can get acsess to the inside of the bumper. You will then see a 10mm bolt towards the top of the bumper that is reversed to you. Remove then the bumper should then just pull away.

Becareful not to damage the fog lamp harness upon removal

Apr 08, 2010 | 2004 Jaguar X-Type

1 Answer

How do i remove the front bumper on a 2005 Hyundai Tucson?


Please leave 4 thumbs up for this answer.
Under the fron wheel arches remove the retaining screws that attach the splash shields to the bumper, Also remove the 2 screws under there that secure the bumper to the corner of the car panel. Remove the grill and supporting clips that attach the bar to the reo {reonforcement} underneath, remove the screws securing the stone shield panels to the bottom of the bar. If you have flood or spot lights, ensure their mountings are free from attaching between the plastic cover and the reo. The cover should pry away with very little force if any. Hope this helps you, safe driving.

Jan 19, 2010 | 2005 Hyundai Tucson

1 Answer

How do you remove headlight unit on volvo v70 2002


Hedadlight removel Volvo V70 2002

Yes the full front bumper has to be removed. Not as bad as it sounds just take your time. One fixing screw in each wheel arch, two bolts behind black bumper trim each side of no. plate, and five or six plastic
plugs on slam panel. Remember to unplug fog lights if fitted. The lamp unit can then be removed secured by thee bolts two on slam panel and one on the inner side of the lamp near the radiator and a clip on the outer side, obvious when you take a good look and dont try to rush.
I hope this will help anyone else.

Nov 01, 2009 | 2002 Volvo V70

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...