Question about Oldsmobile Silhouette

Open Question

Trying to remove oil pan,2002 olds silhouette,have removed r/lower engine mount and supported engine.appears that a/c compressor and starter may have to be removed as well.3.4 liter la1 engine

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: i have a 1996 chrysler

You need to hold the engine on a trolley jack by lifting it on the oil pan itself to then undo the engine mount. Once the mount is removed lower the jack, remove the remaining pan bolts and then remove the pan proper. Refitting is a matter of fitting the pan with some of the bolts, loosely, to then lift the engine a little with the jack to refit the mount, followed by fitting the remaining pan bolts and tightening. Its a matter of just doing things in a certain order but it is easy enough when you do that.

Posted on Mar 02, 2011

Ad
  • 104 Answers

SOURCE: trying to remove oil pan,have

what kind of vehicle

Posted on May 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing oil pan gasket 1998 chevy silverado 305 cu.in.


REMOVAL PROCEDURE
  1. Remove the oil level indicator tube.
  2. Raise the vehicle.
  3. Remove the engine oil and the engine oil filter.
  4. Remove the oil filter adapter.
  5. Remove the starter.
  6. Remove the flywheel inspection cover.
  7. Remove the engine mount through bolts.
  8. Raise and support the engine.




  1. Remove the oil pan nuts and bolts. Note the location of any studs to assist reassembly.
  2. Remove the engine oil pan and the gasket.
  3. Clean all sealing surfaces. Refer to Oil Pan Clean and Inspect under Engine Unit Repair.
INSTALLATION PROCEDURE


  1. Install the engine oil pan and a NEW gasket. Refer to Oil Pan Installation under Engine Unit Repair.
  2. Lower the engine onto the mounts.
  3. Install the engine mount through-bolts.
  4. Install the starter.
  5. Install the flywheel inspection cover.
  6. Install the engine oil filter and the engine oil.
  7. Install the oil filter adapter.
  8. Install the oil level indicator tube.

May 04, 2015 | 1998 Chevrolet Chevrolet silverado

1 Answer

Oil Pan Gasket Replacement/ Oil Pan removal


yes the starter does have to be removed but also the engine mounts must be also as the engine must be raised about 10 " to get the pan out. if you do try this make sure you have very very sturdy jack stands for the engine to just a jack as the jack will lift it but wont maintain it long enough to safely remove the pan and reinstall it......good luck and be very carefull

Aug 11, 2014 | 1998 Oldsmobile Silhouette

1 Answer

How to remove oil pan



4x4
1. Open the hood.
2. Disconnect the battery negative cables.
3. Remove the intake air assembly.
4. Remove the radiator shroud retaining bolts.
5. Install engine support fixture # 8534B .
6. Raise and support the vehicle.

WARNING: HOT OIL CAN CAUSE PERSONAL INJURY.


7. Drain the engine oil (Refer to 09 - Engine/Lubrication/OIL - Standard Procedure) .
8. Loosen the front engine mount bolts.
9. Lower the vehicle.
10. Use the engine support fixture # 8534B to raise engine out of the front mounts.
11. Remove the engine oil dipstick.
12. Raise and support the vehicle.
13. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
14. Remove oil pan and suction tube.
15. Remove the 2 bolts from the front of the engine block stiffener.
16. Remove the oil pan.


4x2
1. Open the hood.
2. Remove the negative battery cables.
3. Raise and support the vehicle.
4. Remove the transmission oil cooler lines.
5. Remove the propeller shaft.
6. Remove the starter bolts.
7. Support the starter.
8. Remove the torque converter bolts.
9. Remove the exhaust hanger bolts.
10. Remove the gear shift cable.
11. Remove the wiring harness.
12. Remove the transmission mount.
13. Remove the crossover bolts.
14. Position the transmission jack.
15. Remove the bell housing bolts.
16. Remove the transmission.
17. Remove the flywheel housing bolts (8).
18. Remove the flex plate bolts (8).
19. Remove the engine oil dip stick.
20. Drain the oil.
21. Remove the steering rack bolts.
22. Remove the oil pan bolts.
23. Remove the oil pickup bolts.
24. Remove the oil pan. user_online.gif

Aug 01, 2014 | Dodge Ram 3500 Cars & Trucks

1 Answer

How to replace oil pan gasket


1994-96 VEHICLES
( see Figures 6 and 7 / click image for zoom )


zjlimited_1359.jpg

Fig. 6: Oil pan mounting bolt locations-1996 3.1L engine shown

zjlimited_1360.jpg

Fig. 7: Oil pan sealant application points-1996 3.1L engine shown

  1. Disconnect the negative battery cable.
It may be necessary to remove the hood, with the help of an assistant, for access.
  1. Remove the engine mount strut and A/C compressor (if equipped) and the engine mount strut bracket assemblies.
  2. Remove the electric cooling fan assemblies. -28467 and J 26462, or equivalent.
  3. Raise and safely support the vehicle. Drain the engine oil.
  4. Remove the front exhaust manifold pipe.
  5. Remove the intermediate shaft bolt/screw.
  6. Remove the oil level sensor.
  7. Remove the engine splash shield.
  8. Suitable support the drivetrain and front suspension with jack stands.
  9. Remove the transaxle mount side frame retaining nuts from the drivetrain and suspension frame assembly.
  10. Remove the engine mount side frame nuts from the drivetrain and suspension frame assembly.
  11. Unfasten the rear drivetrain and front suspension frame bolts/screws.
  12. If equipped, remove the lower drivetrain and front suspension frame bolts/screws.
  13. Remove the engine mount assembly.
  14. Remove the flywheel inspection cover.
  15. Remove the starter.
  16. Disconnect the transaxle mount assembly from the oil pan.
  17. Unfasten the side bolts and screws and the retaining bolts and screws, then remove the oil pan. Remove and discard the oil pan gasket.
To install:
  1. Clean the gasket mating surfaces.
  2. Apply a small amount of sealer on either side of the rear main bearing cap, where the seal surface on the cap meets the cylinder block. Install a new gasket on the oil pan.
  3. Position the oil pan and secure with the retaining bolts and screws. Tighten the retaining bolts and screws to 18 ft. lbs. (25 Nm) and the side bolts/screws using tool J 39505 or equivalent.
  4. Fasten the transaxle mount assembly to the oil pan.
  5. Install the starter motor.
  6. Install the flywheel inspection cover.
  7. Install the engine mount assembly.
  8. Carefully raise the drivetrain and front suspension assembly. Install the rear drivetrain and front suspension frame bolts/screws.
  9. Fasten the engine mount frame side nuts to the drivetrain and front suspension frame assembly. Install the transaxle mount frame side nuts to the drivetrain and suspension frame assembly.
  10. Remove the jackstands from the drivetrain and front suspension frame assembly.
  11. Install the engine splash shield and the oil level sensor.
  12. Install the intermediate steering shaft bolt/screw. Connect the front exhaust manifold pipe.
  13. Carefully lower the vehicle.
  14. Remove the engine support tools.
  15. Install the electric cooling fan assemblies.
  16. Install the engine mount strut and A/C compressor, bracket and the engine mount strut bracket.
  17. If removed, install the hood assembly.
  18. Fill the crankcase to the correct level. Connect the negative battery cable. Run the engine to normal operating temperature and check for leaks.
Hope this helps (remember to rate this answer).

Jun 04, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

I have taken the oil pan bolts out and there is not enough clearance to remove the pan on a 2002 Buick Regal 3800 to replace the gasket. What steps do you suggest next.


Did you remove the catalytic converter, and motor mount? Lots of stuff has to come off to get this pan out. :o(

3.8L Engine
  1. Drain the engine oil.
  2. Remove or disconnect the following:

    Negative battery cable Throttle body air inlet duct Engine mount struts Accessory drive belt
  3. Install an engine support fixture.

    Catalytic converter from the right exhaust manifold Right front wheel Right side splash shield Oil filter and discard A/C compressor bracket and reposition the compressor Power steering oil cooler pipe brackets from the frame Engine mount bracket bolts Lower engine mount nuts Torque converter cover Oil level sensor electrical connector Oil level sensor
  4. Raise the vehicle and place a support under the frame.

    Right side frame bolts and loosen the left side bolts Engine mount and bracket Oil pan

Nov 21, 2010 | 2002 Buick Regal

2 Answers

I HAVE A 2007 2500 DODGE RAM WITH 5.9 CUMMINS AND AUTOMATIC. CAN I LOOSEN THE MOTOR MOUNTS AND LIFT THE ENGINE ENOUGH TO REPLACE THE OIL PAN?


depends on whether you have 2WD or 4WD. The manual says if you have 2WD you have to remove the tranny,but not if you have 4WD. See procedures below.

5.9L & 6.7L Diesel Engines
2WD Models

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Open the hood.
  3. Remove the negative battery cables.
  4. Raise and support the vehicle.
  5. Remove the transmission oil cooler lines.
  6. Remove the propeller shaft.
  7. Remove the starter bolts.
  8. Support the starter.
  9. Remove the torque converter bolts.
  10. Remove the exhaust hanger bolts.
  11. Remove the gear shift cable.
  12. Remove the wiring harness.
  13. Remove the transmission mount.
  14. Remove the crossover bolts.
  15. Position the transmission jack.
  16. Remove the bell housing bolts.
  17. Remove the transmission.
  18. Remove the flywheel housing bolts (8).
  19. Remove the flex plate bolts (8).
  20. Remove the engine oil dip stick.
  21. Drain the oil.
  22. Remove the steering rack bolts.
  23. Remove the oil pan bolts.
  24. Remove the oil pickup bolts.
  25. Remove the oil pan.

4WD Models
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Open the hood.
  3. Disconnect the battery negative cables.
  4. Remove the intake air assembly.
  5. Remove the radiator shroud retaining bolts.
  6. Install engine support fixture No. 8534B.
  7. Raise and support the vehicle.
  8. Drain the engine oil.
  9. Loosen the front engine mount bolts.
  10. Lower the vehicle.
  11. Use the engine support fixture No. 8534B to raise engine out of the front mounts.
  12. Remove the engine oil dipstick.
  13. Raise and support the vehicle.
  14. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
  15. Remove oil pan and suction tube.
  16. Remove the 2 bolts from the front of the engine block stiffener.
  17. Remove the oil pan.

Oct 30, 2010 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

Need to change oil pan


e
Cavalier, Sunfire 2001-2005

Oil Pan - Removal & Installation

2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Right front wheel Right inner fender splash shield Starter motor and bracket Engine mount strut bracket Oil pan
To install:


672c0b8.jpg

Fig. Exploded view of the oil pan mounting and related components-2.2L (VIN 4) engine
  1. Place a 2mm bead of RTV sealer to the oil pan sealing surface except at the rear seal mounting surface. Using a new oil pan rear seal, apply a thin coat of RTV sealer on the end down to the ears.
  2. Install or connect the following:
    Oil pan with a new gasket. Torque the nuts and bolts to 89 inch lbs. (10 Nm). Engine mount strut bracket. Torque the bolts to 49 ft. lbs. (66 Nm). Starter motor and bracket. Torque the bolts to 37 ft. lbs. (50 Nm). Right fender splash shield Right front wheel. Torque the nuts to 100 ft. lbs. (140 Nm). Negative battery cable
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.
2.2L (VIN F) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine mount strut bracket Drive belt Lower then upper AC compressor bolts Oil pan bolts Oil pan

    1c9e9c9.jpg

    Fig. Remove/Install the oil pan bolts in this sequence-2.2L (VIN F) engine
To install:
  1. Apply a 2 mm bead of RTV sealant around the perimeter of the oil pan and the oil suction port opening. Do not over apply the RTV. More than a 2 mm bead is not required.
  2. Install or connect the following:
    Oil pan and tighten the bolts to 18 ft. lbs. (25 Nm) AC compressor bolts Engine mount bracket Drive belt
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.

2.4L Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Flywheel/converter cover Right wheel Right wheel well splash shield Accessory drive belt Air conditioning compressor lower bolts Transmission-to-engine brace Engine mount strut bracket Radiator outlet pipe bolts Radiator outlet pipe from the oil pan Oil pan to the flywheel cover bolt and nut Flywheel cover stud for clearance Radiator outlet pipe from the lower radiator hose and oil pan Oil level sensor connector Oil pan
To install:
  1. Inspect the oil pan gasket; it is reusable if not damaged.
  2. Install or connect the following:
    Oil pan with the gasket. Torque the M8 bolts to 18 ft. lbs. (24 Nm) and the M6 bolts to 106 inch lbs. (12 Nm).

    2ffc5e9.jpg

    Fig. Oil pan fastener torque specifications-2.4L engine
    Oil pan to the transmission nut Oil level sensor connector Radiator outlet pipe to the lower radiator hose and oil pan Exhaust manifold brace Radiator outlet pipe. Torque the bolts to 124 inch lbs. (14 Nm). Engine mount strut bracket. Torque the bolts to 55 ft. lbs. (75 Nm). Transmission to the engine brace Air conditioning compressor lower bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Accessory drive belt Right splash shield Right front wheel Flywheel/converter cover Negative battery cable
  3. Refill the crankcase.
  4. Refill the cooling system.
  5. Start the vehicle and verify no leaks.

Hope helped (remember rated this help). Good luck.

Oct 22, 2009 | 2001 Chevrolet Cavalier

1 Answer

How can i get the oil pan out on a 2001 chevy malibu?


2.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan


  1. Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm).
  2. Accessory drive belt
  3. Negative battery cable

  4. Fill the engine with oil to the correct level.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan

To install:
  1. Apply a 0.13 inch (3.5mm) bead of the GM P/N 12378521 sealant around the perimeter of the oil pan and oil suction port opening.
  2. Install or connect the following:

    Oil pan. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).

    0900c1528024bb26.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Oil pan bolt sequence-2.2L engine
    Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm). Accessory drive belt Negative battery cable
  3. Fill the engine with oil to the correct level.
3.1L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Evacuate and recover the A/C system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    WARNING DO NOT disconnect the refrigerant lines or allow the compressor to hang unsupported.


    Negative battery cable Accessory drive belt Upper and lower radiator hoses Right front wheel Inner fender splash shield Antilock Brake System (ABS) Wheel Speed Sensor (WSS) electrical connector Right front ball joint from the steering knuckle Right side outer tie rod end A/C compressor bolts and move the compressor aside


    Evaporator-to-accumulator A/C line Flywheel cover Engine cradle bolts Crankshaft balancer Starter motor Oil pan

To install:

0900c1528024bb27.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the oil pan mounting-3.1L and 3.5L engines

  1. Install or connect the following:

Sep 02, 2009 | 2001 Chevrolet Malibu

1 Answer

2000 chevy cavalier oil pan....2.2 lit....auto


put car on stands

remove right side engine splash shield

remove exhaust shield

remove AC brace at starter/ compressor bracket

remove flywheel inspection plate

remove engine mount strut, remove bolts from bracket. Lower the bracket slightly to gain clearance to remove pan.

remove oil filter extension (auto trans. only)

remove all pan bolts

tap pan with rubber hammer to break old gasket loose from block.

clean all used gasket off and install is reverse

Mar 13, 2009 | 2000 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...