Question about 1995 GMC Sierra C1500

1 Answer

How do I replace a faulty ignition swith - 1995 GMC Sierra C1500

Posted by on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,510 Answers

You will have to remove all the cowlings from the steering column to access the ignition lock and switch. With the correct key inserted and selected to, probably, the ACC position, you should be able to push on either a pin or a tongue that protrudes from the switch into the housing and the pull the whole lock/switch mechanism out.

Posted on May 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Igintion switch


Electrical portion of the ignition swith is faulty. Replace that and all will be well. A good rule to follow since this a weak point on most of hondas older model cars is the lighter the key chain the longer the life of the electrical portion of the ignition switch.

Oct 07, 2012 | 1992 Honda Accord

1 Answer

97 lincoln mark viii oil pressure light always on. oil pressure good. new sender


test the faulty lamp , turn on the ignition switch to the START position The providing circuit shoudl ligh the warning lamp. If hte light does not come ON during the porve/out, disconnect the sender switch lead. Use a jumper wire to connect the sender switch lead to ground . With the ignition in the RUN position, the warning lamp shoud light. If the lamp is iluminated, replace the sending swith. If the light does not come on, either the bubl is buned out or the wiring is damaged.
God bless you

Sep 28, 2012 | Cars & Trucks

2 Answers

Nissan wingroad 2003 switching off on its own


Hi Njuguna. Undertake computer diagnosis of the engine, probably the crankshaft sensor is faulty and needs replacement. It could also be due to weak battery that will equally require replacement.

Mar 06, 2012 | Cars & Trucks

2 Answers

94 civic wont start, only if i push start it. changed starter and ingnation swith.


SOUND LIKE FAULTY STARTER CLUTCH INTERLOCK SWITCH LOCATED NEAR THE UPPER END OF THE CLUTCH PEDAL OR YOU HAVE A FAULTY STARTER RELAY.CHECK TO SEE IF POWER GOING TO THE CLUTCH INTERLOCK SWITCH WIRES WHEN CLUTCH PEDAL PRESS DOWN. IS YES SWITCH IS BAD.IF NO POWER GOING TO CLUTCH INTERLOCK SWITCH YOU HAVE FAULTY STARTER RELAY OR BLOWN STARTER FUSE.

May 04, 2011 | 1994 Honda Civic

2 Answers

My nissan frontier 2000 v6 is not firing what can be the cause


Sparks plugs, spark plugs wires, coils, defective battery or fusible link.
Ignition swith faulty

Jun 26, 2010 | 2000 Nissan Frontier

3 Answers

I start my car but it immediatly shuts off and the theft sys light flashes could this light be the reason?


the ignition swith reads the key chip when key is turned, this is a common problem,the ignition switch will need to be replaced, after replacing the swith reprograming will be needed, to program you will need a battery charger to keep battery from going dead, after installing new switch,turn charger on, turn key to crank then release key leaving ignition on, you will see the dash lights, leave key on for about 15-20 min, until you see theft light go out, if light doesnt go out then repeat process,crank for 2 sec, then leave key on 15-20 mins until security/theft light goes out, hope this helps.

May 09, 2010 | 1997 Pontiac Grand Am

1 Answer

How do you replace the ignition swith?


the ignition switch is actually on the steering column below the steering wheel. after removing any plastic that might be in the way you will see a metal rod that moves up and down when the key is turned, where the metal rod ends going down is the ignition switch.

Dec 30, 2009 | 1997 Chevrolet Suburban

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...