Question about GMC C1500

1 Answer

Trying to remove and replace starter on my 1992 GMC 1500 series pickup truck. Are the 2 bolts that I see from under the truck the bolts that I remove to take the starter off? I'm not sure if it is a sierra or not.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 134 Answers

Yes its 2 14mm bolts

Posted on May 19, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just need the instructions on how to change the starter on a 1998 GMC 1500 with a 4.3.


start by diconnecting the negative battery terminal, Locate the starter under the truck, should be 2 bolts verticaly though the starter. Loosen both of the bolts but do not remove them. On top of the starter their should be a large and a small wire connected disconnect both of them ( if u cant reach or see them remove the starter by taking out the 2 verticle bolts then remover wires) once bolts and wires are off the starter just wiggle it into postion and remove between the motor/ exausht and frame. Try to remember how it comes out will make it simpler to fit going back in. if thier isnt enough clearence u may have to notch the frame or loosen the motor mounts and raise the engine slight with a floor jack.,

Jan 31, 2011 | GMC C1500 Cars & Trucks

1 Answer

How do you remove and replace a starter for a 1992 2.6L Isuzu Amigo?


1.The battery negative and more importantly positive cable must be disconnected.
2. There are 2 14mm bolts holding the starter in place, the upper bolt can be removed by leaning over into the engine compartment from under the hood with a socket and extension on a ratchet or a ratcheting wrench.
3. crawl under the front passenger wheel and remove the positive cable nut, remove positive cable from starter.
4. unclip the small ground wire attached to starter.
5. remove the lower starter bolt.
6. There is room on the bottom of the vehicle to wiggle the starter down to the floor and out from under the vehicle. There isn't enough room to get the starter out from the engine compartment up and out from under the hood.
7. installation of new starter is reverse of installation.

This procedure should work on any Isuzu Rodeo, Trooper, Amigo, or Honda Passport with a 2.6L 4 cylinder 4ZE1 engine

Nov 12, 2010 | 1992 Isuzu Amigo

1 Answer

What size wrench do I need for the bolts to replace the starter motor on 1988 gmc 1500 with a 305 engine


Hi,
9/16 socket with an extension an a ratchet.
They will be pretty tight so a 1/2 inch drive will help break them loose.
Good Luck
Wayne

Oct 12, 2010 | 1992 GMC Sierra K1500

1 Answer

Replacing starter on 1992 gmc sierra 305 v8 motor


disconnect the battery lead from the starter plus other wires,undo the bolts on the starter flange & the starter should pull straight out providing there is nothing else in the way if there is anything it will have to be removed first.......hope this helps......cheers

Jul 29, 2010 | 1992 GMC Sierra K1500

1 Answer

Where to find diagram to install whole rear brake lines on 1992 GMC Sierra 1500 series pickup truck


I don't know about a diagram. Just buy some 1/4 inch brake line and run it as close to the original as you can.

Apr 03, 2010 | 1992 GMC Sierra K1500

1 Answer

I have a 1992 gmc 1500 305. turn the key. i get clicking from under the dash. replaced the battery and the starter.


it's possible your starter relay has went bad or you have a dirty /loose connection

Jan 07, 2010 | 1992 GMC Sierra K1500

1 Answer

How to replace a starter on 1994 gmc sierra 1500 with a 350 engine


unhook the battery, there are 2 wires on the starter solenoid, 1 is a 5/16 nut and the other is a 9/16 nut remove those wires. this maybe easier to remove the heat shield first. next ther are two 9/16 bolts holding the starter in position, remove, and the starter will come out, about a 15min job

Sep 27, 2009 | 2000 GMC New Sierra 1500

1 Answer

Starter in a 1992 GMC Sonoma 4.3 v6


bottom rear of engine on the passenger side, the starter is serviced from under the car. it is held to the engine block with two bolts, then u must remove the battery cable and starter solenoid wiring as well, always disconnect the battery before doing any work on the starter.

May 19, 2009 | 1992 GMC Sonoma

1 Answer

1992 toyota pickup need to change the cluch. is there a easy way to do this.???


no easy way.you will need a jack and stands metric tools disconeck batery remove starter and drive line remove shifter ther are 6 bolts you can axis them from the inside of truck by removeing the shifter boot.place a jack under the trasmition remove the trasmition mount and then remove the 6 bellhouseing bolts 14.mmbut first disconeckall wires from the tansmition after all this is you may need help to lower the trans.6 12mm bolts hold the cluch inplace remove and replace cluch.repet proses should take 3hrs to do this

Apr 16, 2009 | 1992 Toyota Pickup

1 Answer

Replace starter on 1992 GMC Sierra pickup truck


First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.

Feb 14, 2009 | 1992 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...