Question about Ford Ranger

1 Answer

What type of rearend grease or oil is to used

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 652 Answers

90 weight.....

Posted on May 19, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What kind of grease to use on motor with no dearings?


[PDF]Guide to Electric Motor Bearing Lubrication - Mobil ...

www.mobilindustrial.com/.../tt-electric-motor-bearing-lubrication-guide....
The base oil used in greases may be mineral or synthetic. Mineral oils are ... electricmotor bearing grease should soften no more than. 1 to 1.5 NLGI grades in ....intervals based on operating conditions and type of grease. Typically, light to ...

Oct 29, 2015 | Cars & Trucks

1 Answer

How do i check the rearend grease 2 make sure it has enough in it on a 1986 chevy monte carlo ls


there is a plug that needs to be removed from the differential and when removed stick your finger in the hole and bend it at the first knuckle.when you remove your finger there should be differential oil on the tip.the level should be at the bottom of the hole.check it with the car level not on an angle.

Apr 25, 2011 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

On my 2003 tahao 4.8L 4x4...the pumpkin on the rearend is leaking fluid from the seal and do not know if its synthetic oil or plaiin gear oil. but i have no owners manuel to find type or weight of oil


If you have a positraction unit (both rear wheels turn in the same direction when turned off the ground) You should use synthetic. Otherwise you can use standard 75/90 or 75/140 lube. If it's leaking you may try adding lucas sealer to slow the leak (read instructions for percentage of additive and product application)

Dec 28, 2010 | 2003 Chevrolet Tahoe

1 Answer

How do i check my rear end fluid


take the plug out of the rearend housing (pumpkin) with a ratchet. Put your finger in the hole, oil should be within a 1/4" from the bottom of the hole, if not, add the proper grease in the hole until it runs out, install plug

Aug 18, 2010 | 1994 Chevrolet C1500

1 Answer

What type off fluid in rearend of 2000 jeep


You have a choice of 75 90 or 75 140 gear oil. I'd opt for the 140 because It gives better film strength under loads. and there is no draw back to using it. If you have a positraction differential don't forget to put in posi additive.

Jun 01, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Gear grease o new brake pads


Hi there. Normally, once you get gear oil on the pads they are toast. The gear oil soaks into them and you can't get rid of it. You will have problems with your brakes locking up if you reuse the contaminated pads. Hope this helps.

Jan 31, 2009 | 1990 GMC Sierra

1 Answer

Rear end noise


Well it can be quiet a job the truck is 13yr old and all the nuts and bolts get rusted and will have to be cut off probly. The dealers go over board some times on what needs to be fixed. What i would try first is remove the rear diff cover and drain all the grease out go to napa or a parts store and buy a product/grease called lucas oil and fill the diff with this and give it a try first if all elese fails i would look around at a junk yard for a used rearend and have them put it in probly be the cheapest way .

Jan 10, 2009 | 1995 Ford Explorer

1 Answer

LOUD NOISE FROM REAREND


remove the the diff unit and refit into your casing ,,,easy job,Preload on pinion bearings and set crownwheel backlash to a very small wiggle woggle.handful of LM grease in unit before you refit cover then use ep90 gear oil .job done shouldnt take more than a morning to do.

Dec 23, 2008 | 1991 Toyota Previa

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...