Question about 1999 Pontiac Grand Prix

1 Answer

I tried removing my fuel filter today and the part was way too rusty I used a lot of force and I still got nothing, I sprayed pb blaster and still got nothing. What am I doing wrong?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has written 2 tips or uploaded 1 video tip.

  • Expert
  • 171 Answers


Usually the fuel filters comes by itself if you loosen all the nuts and screws.

There might be some screw left unscrewed due to which it seems to get jammed .

Kindly observe the fuel filter carefully and look for some possibilites.


Posted on May 19, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The bolts & nuts for the roof rail are rusty & stuck , I need to know how to solve this problem and change the nuts and bolts my car is cherokee laredo 2004

There are a few ways, use a small steel brush and clean them as good as you can then spray some pb blaster on them and let them sit for 2hrs then respray them again and try to loosen then, the other way would be to cut them off, not to sure how much room you have but these are the ways to remove them i think cutting may be the best way to go depending on how rusted they are , the bp blaster is the best stuff i ever used and if you soak them they just may break free.

Sep 24, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

The door ajar light stays on all the time. I tried to push in on the doors, but nothing works. Please help me John M

this is caused by the door ajar switch sticking. easiest and cheapest way to fix this is to spray a generous amount of wd-40/enforcer/pb blaster or like spray chemical into all the door latches. this will free up the sticking switch. spray it into all your door latches since we dont know which switch is sticking and spray a lot of wd-40 onto them

Sep 08, 2010 | Ford Explorer Cars & Trucks

2 Answers

Remove the wheel bearing/hub assembly from the

need detailed pictures of how to change rear wheel bearings on a chevy equinox

Aug 01, 2010 | 2006 Chevrolet Equinox

1 Answer


remove the two fuel lines and two vent hoses then disconnect filler hose and vent next to it you have to let the tank down alittle to get to the elctrical connector two 13mm. bolts are holding the straps in place if thee threads are rusty spray them with pb blaster oh it is easier if the tank is real low on gas you could also take out the driveshaft to make it more accesable hope this helps u out

Mar 24, 2010 | 2008 Ford F 450 Super Duty

1 Answer

2005 Ford F 150 throws p2104 tac system forced idle code frequently.Need advice.

Remove the throttle body and clean the carbon off the throttle plate being carefull not to harm any coating that may be applied from the manf. I use P.B Blaster and a piece of scotch brite pad. spray pleanty P.B on the pad after words clean with a soft cloth. Disconnect the battery to completly clear the code.

Feb 17, 2010 | 2005 Ford F-150

2 Answers

I have a 1989 k1500 350 5.7L. how to remove the fuel filter from the gas tank. It's rusty around the fuel filter and gas tank. I just don't want to miss anything up.

The best think i have found to use on rusty parts is called PB Blaster, It comes in an areosal can that can be purchased at any local parts store such as Autozone or Advanced Auto Parts, Spray some on the rusty parts and let it soak for a little while and it should break free no problem.

I hope this helps, Good Luck, Allen

Oct 04, 2009 | 1989 Chevrolet C1500

2 Answers

How to change fuel pump 1990 cadillac seville

The fuel pump and sending unit is located in the tank. I hope your tank is empty, if not you will need to siphon it out. It is dangerous with the gasoline, and remember the fumes burn, not gas. You start by removing the filler hose, then loosen straps, detach sending unit wire and fuel line, then lower tank. Then unscrew the sending unit/pump and replace. reinstall.

Jul 05, 2009 | 1990 Cadillac SeVille

1 Answer

Door Ajar light and interior lights always on.

the best lube to use for these latch assembleys is PB BLASTER available at your local parts store. spray each latch really good one at a time, then open and close door 10 to 15 times. trust me PB BLASTER takes care of this 90% of the time

Mar 23, 2009 | 2003 Lincoln Town Car

1 Answer

Trunk won't open with interior release or key`

If not used for Long Period of time can seize up last resort go though rear seat to get it open and work with it from there if rusty Use PB BLASTER Spray on it and work it free

Jan 07, 2009 | 1999 Toyota Camry

1 Answer

89 mustang door wont open from the outside.

i think i would spray it again instead of wd40 get some P.B. Blaster works 10x better for loosening rusty try that since it worked before. you can get P.B. Blaster at walmart or parts stores.

Dec 08, 2008 | 1989 Ford Mustang

Not finding what you are looking for?
1999 Pontiac Grand Prix Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides