Question about Isuzu Rodeo

Open Question

2007 Rodeo 3.0ltr Diesel. Loss of clutch pedal pressure. master cyl replaced. What does electric solenoid on back of clutch slave cyl do?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jocko777
  • 7 Answers

SOURCE: Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L

at a minimum the pressure plate but not changing everything while in there would be silly

Posted on Aug 01, 2008

  • 490 Answers

SOURCE: i have A 1998 FORD RANGER EXT. CAB W/ 6 CYL.- 4.0

Take the top off the master cyl and slowly very slow push in on the clutch and watch for any bubbles comming up.Replace the top and pump pressure and bleed at the master direct by using the lines for bleeders.

Posted on Aug 13, 2009

wilsodfarm
  • 986 Answers

SOURCE: hydraulic clutch 1995 chevy 1500 truck

I know you dont want to hear this but it sounds like the clutch plate is in backwards.

Posted on Oct 19, 2009

  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

  • 1 Answer

SOURCE: 2004 cavalier clutch pedal stays on floor,clutch

This appears to be a common problem with 2004 Cavaliers. My 2004 Cavalier just reached 221,000 miles, yes, on one clutch. It finally went out. Here are your best solutions in order: 1-bleed hydraulic line, 2-if there is a leak from inside the transaxle the problem is most likely your clutch release cylinder, it's the fitting at the end of your hydraulic line that plugs into the transaxle from the outside, it's a dealer only item, part# 89060003, the part item is actually called the hydraulic line but it comes with the release cylinder, can't buy the release cylinder by itself, approx. $105.00, 3-if that doesn't fix it, the next step I recommend is replacing the master cylinder simply cause it's cheaper (approx. $75) and easier to replace, 4-if none of those fix it then it's your slave cylinder, I recommend this solution last cause it's the most expensive and time consuming, the transmission must be removed from the vehicle, not for novice do-it-yourselfers, also, if this step is required then I suggest you replace the clutch and pressure plate as they will be exposed also since you're going to have the transmission out anyway

Posted on Jul 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced clutch mastercylinder clutch pedal is hard will not push down


Can you see the clutch slave cyl?
Is it extended fully?
Is this condition after you bled the system?
Try opening the bleeder on the slave cyl in case you have full pressure in the system right now.Also make sure the new master cyl rod from the clutch pedal allows the master cyl to return fully to it's retracted position or the pressure will build up an lock the pedal as yours is.
You want a little play in the clutch pedal rod to master cyl.

Apr 08, 2017 | Cars & Trucks

1 Answer

Trying to find leak in clutch system os 1993 rodeo need diagram


Did you bench bleed the master or slave cylinder ? Is Your Brake pedal Hard ? Could be your Brake booster . send image for more understanding of your problem

Feb 25, 2014 | 1993 Isuzu Rodeo

2 Answers

There is no pressure when i press down my clutch, I just had it replaced about a year and a half ago. It didn't feel like the clutch went?


clutch master or slave cyl. could have gone out so you are no longer releasing clutch thats why no pressure on pedal. look for Brake fluid leak -clutch uses same type of fluid. or master cyl can leak or bypass internally and just not build pressure.

Jan 24, 2011 | 2001 Hyundai Elantra

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

2 Answers

Can't change gears with car running, noticed that fluid was low in clutch cup, whats wrong?


your clutch master cylinder which connects to the clutch pedal is leaking or the slave cylinder on the gearbox is leaking,look under dash and pull back the rubber cover at the back of the master cyl,its where the rod comes out and connects to the pedal pull the rubber cover back on the slave cyl if you see dampness or fluid in one of these areas it needs to be replaced or overhauled,it will be one of these things

Nov 15, 2009 | 2003 Toyota Corolla

1 Answer

I have A 1998 FORD RANGER EXT. CAB W/ 6 CYL.- 4.0 RECENTLY LOST PEDAL ON MY CLUTCH. REPLACED MASTER CYLINDER, SLAVE CYLINDER, AND THE CLUTCH PACK, HAVE FLUID THROUGH BLEEDER VALVE ON THE SLAVE BUT CAN NOT...


Take the top off the master cyl and slowly very slow push in on the clutch and watch for any bubbles comming up.Replace the top and pump pressure and bleed at the master direct by using the lines for bleeders.

Aug 13, 2009 | 1998 Ford Ranger SuperCab

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

2 Answers

The clutch in our 2004 mitsubishi just let go and now the pedal has no "push back" is there potentially a fluid issue


check the resivior for fluid if it is empty then either the slave cyl or master cyl or possibly both are leaking

May 10, 2009 | 2004 Mitsubishi Eclipse

3 Answers

Clutch pedal doesnt spring back up


Have you tried bleeding the clutch. Is it losing fluid?

May 03, 2009 | 1985 Toyota Celica Supra

1 Answer

Clutch pedal low near floor, can the clutch be adjusted?


hi the clutch on accent is hydraulic operation so if pedal is very low on disengaging clutch ? you may have a problem with the hydraulics 1st thing to check is fluid level? this is the reservoir that feeds both brakes and clutch but is seperaterated inside if fluid low? top up and bleed the slave cyl however if fluid low indicates a leak ? possibly slave cyl? if no loss of fluid ? then prob may be fault in the master cyl ? check fluid come back with any update please ps if this problem has just occured? check for leaks ?

Feb 02, 2009 | 2005 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...