Question about 1985 Dodge Ram 3500

Open Question

Engine SWAP 360 to 318 Dodge Ram

Had a 360 engine replacing with 318 wont slide into bushing??? Its a dodge ram 350 dumptruck. I have taken out all parts and they all fit until i go to mount engine into transmission keeps missing by 1/2 inch. Need Help!

Posted by on

6 Suggested Answers

  • 10 Answers

SOURCE: need firing order on a 1996 dodge ram v8

The order should be stamped on your intake manifold right under the air cleaner.
My '97 1500, 5.2, 318 firing order is 1-8-4-3-6-5-7-2

Hope this helps

Posted on Sep 17, 2008

tommypollock
  • 28 Answers

SOURCE: engine swap

I just put a 96 360 magnum in my 97 dodge 4x4 that had a 318 in it. Yes it does fit. I noticed that the flex plate on the 360 has balance weights on it and the 318 does not. Make sure the plate stays with the 360. The torque converter and exhaust manifolds bolted right up. The 96 360 engine had different connector plugs on the Map sensor, Crank Sensor and Tps. Get those off of your 318.
I did notice that with the 96 PCM for the 360 my fuel guage was off quite a bit. The 360 will run off of the 318 computer at least if your in a bind for Money.

Posted on Oct 08, 2008

motor1258
  • 6674 Answers

SOURCE: belt diagram 2004 5.7 liter engine dodge ram 1500 1/2 ton 4x4

click on this link, and scroll down to 5.7L

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800ba71e

Posted on Dec 22, 2008

  • 412 Answers

SOURCE: Dodge Ram 2500 4x4 running lights stay on after engine is off

IT SOUNDS LIKE THE DAYTIME RUNNING MODULE HAS FAILED..BEHIND FUSE BLOCK UNDERHOOD ON INNER FENDER..UNPLUG IT..IF LIGHTS GO OUT,YOU NEED A MODULE..ABOUT 100 BUCKS AT DEALER

Posted on Sep 20, 2009

  • 2 Answers

SOURCE: 1983 dodge power ram 150 custom pickup truck

On the drivers side bottom of the tranny, there should be embossed numbers on the tranny housing. I have a 1983 dodge ram also. It has a 318 with 727 trans.

Posted on Nov 15, 2009

cmcduncand
  • 714 Answers

SOURCE: shifter linkage to transmission: bushing and clip mount?

Broken grommet in shift linkage.

Hope this tip helps

R/
David

Posted on Feb 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 dodge ram 5.2 motor swapped out of a 1996 dodge ram turns but don't start


Is it possible that you did not swap the ECM module along with the engine

May 31, 2015 | Dodge Ram Cars & Trucks

1 Answer

1993 dodge 350 1 ton 2 wheel drive shaking in frount end replaced ball joints stablelizer bushings replaced tires twice with new ones replaced rims replaced rotors replaced a-arm bushings no play in tie...


I had this problem also. I had the rims cleaned, balanced the wheels and replaced the shocks. Each action helped a bit but replacing the shocks was the most improvement.

Dec 21, 2010 | 1993 Dodge Ram 350

1 Answer

Do you have to raise the engine to remove the oil pan on a 1989 dodge ram 350 with a 5.9 engine?


yes, dont smash the distributor against the firewall when you lift it

Oct 20, 2010 | 1991 Dodge Ram 350

2 Answers

1999 Dodge Ram 1500 318 engine no spark no signal to coil i changed cam positioner sensor and crank positioner sensor still no spark could it be a bad wire (ground)somewere


Check the ASD relay in the fuse box. Swap it with the starting relay. If the engine fails to roll over. Thats your problem. If not, check and see if your fuel injector connectors have voltage to them if not its a bad PCM. Hope this helps.

Jun 05, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

Replaced front seal on my '97 Dodge Ram 1500, V6


Assembly of converter to trans and then tunit to engine? The torque converter must engage and slide into the front pump. The seal is easily damamaged if not properly fitted.Once the trans is against the engine the converter can be slid forward to bolt the flex plste.There should not be more than approx. 1/4 inch between the converter and trans bell housing if the converter is properly mated to the trans. Good Luck, Ned.

Jun 01, 2010 | 1997 Dodge Ram 1500 Club Cab

1 Answer

1993 dodge Ram 350 fluid specifications


assuming you need fluid type?
transmission - atf 4
engine oil
10w30 above oF
5w30 below 60F
differential - gl-5

Mar 11, 2010 | 1993 Dodge Ram 350

1 Answer

1988 Dodge Ram 350 van wont fire or start?


first is first check battery and alternator

Feb 24, 2010 | Dodge Ram 350 Cars & Trucks

1 Answer

Dodge ram50 1992 swap 2,4L to 2,6L


Greetings!

Yes, the engine mounts and bell housings are the same.
The swap should be straight forward, however be sure to swap all the vaccum controls and emission system from the 2.6L.

Have fun!
Cheers, Jay

Apr 29, 2009 | 1992 Dodge Power Ram 50

1 Answer

How do i change oil pan on 1999 dodge ram 1500 with 5.2 magnum


Remove dipstick, exhaust pipe, left engine to transmission mount, loosen motor mounts & raise engine slightly.(enough to slide pan back out, when ready.) Heard enough yet? Good Luck.

Apr 19, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

674 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...