Question about Toyota Camry

Open Question

What is the torque for the inner tie rod of a toyota camry 1997

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: 1997 dodge Intrepid: inner tie rod

To Steering Gear Bolt 90 Nm (66 ft. lbs.) Jam Nut 75 Nm (55 ft. lbs.)
NUMBER: 19-001-01
GROUP: Steering
DATE: Mar. 23, 2001
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 19-003-00 REV A, DATED OCTOBER 6, 2000 WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE PART NUMBER CHANGES AND ADDITIONAL MODEL YEAR.
WARNING: FAILURE TO ACHIEVE A MINIMUM TORQUE OF 100 NM (74 FT. LBS.) MAY RESULT IN THE ATTACHING BOLTS LOOSENING AND FRACTURING. THIS COULD RESULT IN A SUBSEQUENT LOSS OF STEERING CONTROL. BENDING THE RETAINING TABS ALONE WILL NOT PREVENT THIS.

SUBJECT:
Loose Steering

OVERVIEW:
This bulletin provides service procedures and parts information for the inner tie rod bushings.
MODELS:
1993 - **2001 ** (LH) Concorde/Intrepid/LHS/New Yorker/Vision/300M
SYMPTOM/CONDITION:
Loose feel or clunk in the steering wheel as the wheel is moved from side to side.
DIAGNOSIS:
Observe the inner tie rod to steering gear attaching point while moving the steering wheel from side to side. If there is movement between the gear and inner tie rod, perform the Repair Procedure. If no movement is evident further diagnosis of the condition will be required.
DISCUSSION:
The inner tie rod bushings have previously been serviced with the tie rod assembly. This bulletin releases the parts, service procedures, and special tool necessary to service just the bushings. Subsequent service manuals will contain the Repair Procedure.

Posted on Jan 13, 2009

chuck943
  • 783 Answers

SOURCE: 97 taurus GL inner tie rods

You have to have a special tool like this
http://motors.shop.ebay.com/items/Parts-Accessories_Automotive-Tools__W0QQ_nkwZfordQ20innerQ20tieQ20rodQ20toolQQ_fromfsbZQQ_trksidZm270Q2el1313QQ_odkwZQQ_osacatZPartsQ2dAccessoriesQ5fAutomotiveQ2dTools

Disconnect the outer tie rod and remove,then remove boot,then use special tool to remove inner tie rod. You will then have to have it aligned. You can use a tape measure to get it close enough to drive,just mark one of the grooves in the tire so you are measuring the exact same points,measure from tire to tire in the front of front tires then take a measurement at the rear of front tires and adjust the outer tire rods until the measurements are pretty close to equal.

Posted on Feb 17, 2009

  • 4369 Answers

SOURCE: How to change inner tie rod ends?

if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------

  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Posted on Apr 15, 2009

GARYca
  • 672 Answers

SOURCE: 97 a toyota camry do they have replacable inner tie rod ends

they do have replaceable inner and outer tie rod ends, although I do recommend replacing the entire rack and pinion!! Hopefully this helps!!

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1996 toyota camry is shaking a lot


1st check air pressure in tires make sure they are all set to 35psi.
If that don't fix it
2nd it would be out of line. Front end alignment will be needed.
3rd inner tie Rod ends may be worn out.
If you fix all of these and your problem still exist then it would be your inner tie rods.

But 1st i would check pressure in tires and go from there.

Aug 21, 2016 | 1996 Toyota Camry

1 Answer

What is the torque specs for a tie rod end on a 1994 toyota camry


The tie rod end adjusting nut, 54 ft lb or 74 Nm
The tie rod end ball joint nut, 36 ft lb or 49 Nm

May 10, 2014 | 1994 Toyota Camry

1 Answer

Rear tie rod adjustment sleeve/pulls to right/1997 toyota


are they incompetent?
the dont makes excuses, they do, or order parts.
find a real ASE mech. yours, is noob.

had it looked at , is the uncle fester or what?
wreck?
my guess, is cant wrench turn the tie rod adjustments do to rust.
buy a new rod, or use a torch and heat cycle it, all mech now what to do , Pen oil, then heat then buy new one.

Jan 02, 2014 | 1997 Toyota Camry

1 Answer

Toyota camary 1995 end tie rod digram


you need to either be able to get a wrench on the Inner Nut or you need the special tool to get the Inner Off. The Correct tool makes it an EASY Job..
65f5515d-4238-4aaf-9e87-134a665da60c.jpg

Apr 16, 2013 | 1995 Toyota Camry

1 Answer

WHAT ELSE SHOULD I CHANGE WHEN I AM CHANGING REAR STRUTS ON 94 CAMRY


On the struts, it will depend a bit on what you find, but I would also replace the bounce buffers, upper and low spring seat rubbers and maybe the strut upper bearing plates if they have been noisy at all. They do wear.

Have a close look at the bushings in the lower lateral arms and the torque rods (drag links). I would replace the sway bar mount bushings as they are notorious on this car for wearing quickly.

http://www.turboninjas.com/camry/sa.pdf

May 22, 2012 | 1994 Toyota Camry

1 Answer

How to replace a tie rod on 98 toyota camry


With the car off the ground wheel off. Take the cotter pin out from the tie rod. Loosen the castle nut almost all the way. Then with a hammer hit the spindle were the tie rod goe into. Make sure to hit just the hard cast steel of the spidle nothing else. Loosen the locking nut from the tie rod. Mark the spot were the tie rod is or count the revolutions as you are taking it of. So when you install the new one you can get it back in the same place. It is rec. that you still go get and alignment, but if you mark it you will be very close the original position.

Feb 11, 2011 | 1997 Toyota Camry

1 Answer

97 a toyota camry do they have replacable inner tie rod ends


they do have replaceable inner and outer tie rod ends, although I do recommend replacing the entire rack and pinion!! Hopefully this helps!!

Mar 28, 2010 | 1997 Toyota Camry

2 Answers

Noise in sway bar area/94 camry 4 cyl


Possible tranny or engine mount. Check bushings. Check brake pad backing plates (loose), check brake pad movement (add shims), but most likely mounts. you need to torque the engine while an assistant checks for bad mounts.

Aug 31, 2009 | 1994 Toyota Camry

2 Answers

1997 dodge Intrepid: inner tie rod


To Steering Gear Bolt 90 Nm (66 ft. lbs.) Jam Nut 75 Nm (55 ft. lbs.)
NUMBER: 19-001-01
GROUP: Steering
DATE: Mar. 23, 2001
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 19-003-00 REV A, DATED OCTOBER 6, 2000 WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE PART NUMBER CHANGES AND ADDITIONAL MODEL YEAR.
WARNING: FAILURE TO ACHIEVE A MINIMUM TORQUE OF 100 NM (74 FT. LBS.) MAY RESULT IN THE ATTACHING BOLTS LOOSENING AND FRACTURING. THIS COULD RESULT IN A SUBSEQUENT LOSS OF STEERING CONTROL. BENDING THE RETAINING TABS ALONE WILL NOT PREVENT THIS.

SUBJECT:
Loose Steering

OVERVIEW:
This bulletin provides service procedures and parts information for the inner tie rod bushings.
MODELS:
1993 - **2001 ** (LH) Concorde/Intrepid/LHS/New Yorker/Vision/300M
SYMPTOM/CONDITION:
Loose feel or clunk in the steering wheel as the wheel is moved from side to side.
DIAGNOSIS:
Observe the inner tie rod to steering gear attaching point while moving the steering wheel from side to side. If there is movement between the gear and inner tie rod, perform the Repair Procedure. If no movement is evident further diagnosis of the condition will be required.
DISCUSSION:
The inner tie rod bushings have previously been serviced with the tie rod assembly. This bulletin releases the parts, service procedures, and special tool necessary to service just the bushings. Subsequent service manuals will contain the Repair Procedure.

Jan 13, 2009 | 1994 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...