Question about 1998 Ford Contour

1 Answer


Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The diagram is on the right strut tower

Posted on Sep 14, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to add freon to a 1998 ford contour

on a contour its the one on the drivers fact your snap on fill hose will only fit the right one which is the one on the drivers side...let your car run as the Freon goes n and make sure your ac is turned on max cooling

Jul 21, 2015 | 1998 Ford Contour

1 Answer

I need to put 1998 ford contour in time it is a 2.0 where is the timing marks at and supposed to be

Special tools are required, there are no marks on the cams. I would call a local repair shop that works on Fords and ask them to complete the repair.

Mar 18, 2010 | 1998 Ford Contour

2 Answers

How to line up timing marks

2.0 engine does not have cam marks, special tools are needed to time the cams. at the rear of the cams is a slot, and the tool, (flat bar) is inserted, then the cam bolts are tightened. if you dont know what you are doing, take it to a qualified repair shop, you may break the cam

Oct 19, 2009 | 1998 Ford Contour

1 Answer

Replace fanbelt 98 saab 205e

You are going to have to get the tensioner removed and replaced is the only solution.

if you have to, cut the belt to make getting the tensioner removed.

Aug 27, 2009 | 1998 Saab 900

1 Answer

Ford Contour apparently starves for gas, dies.

tell your mechanic to replace the fuel filter. This part is usually less than $10. It should be replaced aout every 50K miles.

Jun 22, 2009 | 1998 Ford Contour

1 Answer

1998 contour fueling problem

Below is a link to a diagram to show you what you're up against. Hope this solves your problem. Best of luck on your repair.

Jun 19, 2009 | 1998 Ford Contour

1 Answer

Misses and hesitates

theres a plastic vacuum line at the back of the intake thats difficult to reach but i have found this broken many times and cause a multitude of problems long shot but check it

May 30, 2009 | 1998 Ford Contour

1 Answer

Back wheel bearings noise

i have a broken down ford contour 1998 i dont know if it will help but when you replace the bearings you have to replace both at the same time or it will end up making the same noise again. go to the parts store, and get TWO bearings. replace them and it should fix the problem.

Oct 20, 2008 | 1998 Ford Contour

1 Answer

Fan belt replacement / xg ute 1996

There is a diagram of the belt run under the hood, the belt has has a spring loaded pulley that tensions it.

Sep 02, 2008 | 1996 Ford Contour

Not finding what you are looking for?
1998 Ford Contour Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

71288 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides