Question about 2002 Chevrolet Monte Carlo

2 Answers

Blower moter works on hi speed onley blower motor blower on hi speed onley

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is the resistor for the blower motor. It needs to be replaced. It is located under the passenger side by the blower motor. A real pain to change out.

Posted on Jan 21, 2013

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 338 Answers

Sounds like diode in motor burned out- replace motor

Posted on May 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2000 dodge dakota blower moter not working replaced blower motor


first when it comes on is it only in the hi position? if so the resistor needs to be replaced again (just because its new does not mean it works) and the blower speed switch in the control panel needs to be replaced

Dec 17, 2012 | Cars & Trucks

1 Answer

Heater controls and blower moter


do you have power at the blower? does it work on any speed?check all fuses and relay. also, look into the blower motor resistor, located next the the blower itself

Nov 03, 2012 | Toyota Tacoma Cars & Trucks

1 Answer

Heater blower dont work from 1 to 3 speed


Most likely cause is the blower motor resistor block. 1,2and 3 go through the resistor forth speed is is full blast therefore bypasses the resistor being the only speed setting that works when the resistor has failed

Jun 13, 2012 | 2004 Ford F150

2 Answers

How do you fix a fan speed control that only works on speeds 3, 4, and 5?


replace blower motor resister this can be found not far from blower moter usally

Dec 14, 2010 | Pontiac Grand Am Cars & Trucks

4 Answers

Blower motor works when it wants sometimes when i hit a bump in the road but not on full capacity


the moter is shot but u could try replacing the blower moter resester it controls the speed of the fan when you select the speed setting.

Nov 29, 2010 | 2002 Cadillac Deville

1 Answer

My heater motor only works on high


A bad blower moter resistor can cause the blower to default to high speed only. The resistor is
located behind the lower right side of the dash on the heater box just left of the blower moter.
The fan switch can also cause this problem, but more often then not it's a bad resistor.
Hope this helps.

Nov 22, 2010 | 2006 Chevrolet Colorado

1 Answer

Blower motor has no speeds put new resister in 4 times works on 3 speeds then stops hocked fan moter up and it works its on a 2000 buick centery


There is a short between the resistor and the motor. Recommend you replace wiring from resistor to the blower.

Sep 04, 2010 | 2000 Buick Century

1 Answer

Blower moter won't run blower good


replace the fan resistor located on the side of the heater box under the dash usually on the passenger side this controls the fan motor speed along with the switch itself.

Dec 08, 2009 | 1999 GMC Safari

4 Answers

What will make a blower in a car only work on high 0n a 1996 sunfire


Could be two things. Heater control..or heater switch. Or the moter is not recieving the reostat info from control. Check at heater wher wires go into it..as you change positions of switch you should see a voltage drop or increase, if u do then the moter is bad...if u do not then replace the heater control unit. :)

Sep 07, 2009 | 1996 Pontiac Sunfire

1 Answer

2005 Kia Sorento only blows hot and cold air on high. Is it a blower motor resistor and if it is where is it located?


If the blower moter only works on hi speed it is the blower motor resistor that is bad. The blower motor resistor is located under the passenger side of the dash next to the blower motor. It is not necessary to remove the blower motor to change the resistor.

May 12, 2009 | 2005 Kia Sorento

Not finding what you are looking for?
2002 Chevrolet Monte Carlo Logo

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...