Question about 1995 Jeep Wrangler

1 Answer

Manual Trans Problem

I have a 95 Jeep Wrangler 2.5 lit., 5 speed manual, that lost the overdrive gear while driving in it.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

You should of stopped and picked it up. just kidding! do you mean it wont go into gear or when it is in gear nothing happens

Posted on Aug 25, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Speedo 95 yj conversion 350 with 350 turbo trans and np231 transfer case 3.73 gears 33" tires wires cut off at transfer case and there is no speedo cable what do i need to get my speedo working


The vehicle speed sensor is located in the transfer case housing. To get your speedometer working you will have to connect the wires back to the speed sensor.

Nov 02, 2011 | 1990 Jeep Wrangler

1 Answer

I have a 89 jeep wrangler with a 2.5 engine and ax-5 trans. it is knocking in all gears but 4th.


may want to do an oil change/filter on trans-then neccisary ajustments from a repair manual--if still persist then rebuild may be in order--trans can last 250 thou miles but heat is the killer

Mar 25, 2011 | 1989 Jeep Wrangler

1 Answer

How much gear oil does the 5 speed manual hold in a 95 full size truck?


Well for starters it is no longer gear oil.A 95 uses synthetic.I have a Getrag M5 95 C1500 5 speed and Think when fully drained it held about 2 1/2 quarts.I buy the trans fluid from GM dealer,not sure if Mobil 1 synthetic 80/90 would be the same.The fluid from the dealer is realy thin.Well hope this helps and good luck.

May 24, 2010 | 1994 GMC Sierra

1 Answer

Jeep 1997 Wrangler. Gear shifting very hard


synchronizers are going bad a used trans would be cheaper than a rebuild due to the labor involved

Aug 19, 2009 | 1997 Jeep Wrangler

2 Answers

Is the overdrive solenoid on a 95 JGC accessible, externally?


no. its part of the valve body inside of the transmission. you would need to drain and remove the transmission oil pan and then remove the valve body. Best left to a transmission shop or reputable repair center.

Aug 10, 2009 | 1995 Jeep Grand Cherokee

1 Answer

95 jeep cheorkee transmission


Bellhousing, driveshaft, crossmember yes. BUT, are we talking overdrive auto or 5 speed manual? P.S. unless you've pulled a tranny before, take it to an expert.

Jun 27, 2009 | 1994 Jeep Grand Cherokee

2 Answers

Hard to get into reverse


try shifting in to first and then reverse. reverse might be worn out. you can have that gear replaced without replacing the whole transmission.

Jun 19, 2009 | 1998 Jeep Wrangler

1 Answer

2000 jeep wrangler are sythetic lubes used in axils and trans


Hello grega1967, your Jeep Wrangler came from the factory with gear oil in the axles and manual transmission, but the transfer case uses transmission fluid. It is a NP231 and your axles are Dana 30 in the front and Dana 35 in the rear. They should have a 4.10 gear ratio due to you having a 2.5 liter 4 cylinder.

I hope this helps,

map6260

Mar 12, 2009 | 2000 Jeep Wrangler

1 Answer

1987 Jeep YJ [Wrangler] so owner ship says''


Our Jeep Wrangler YJ's are equipped with a vacuum module on the front axle. It is used to engage the front axle when the transfercase is shifted into 4WD. Check the vacuum lines on the front axle to make sure they are connected. The passenger side axle shaft has a disconnect sleeve that is moved left and right by the vacuum.

Mar 01, 2009 | 1987 Jeep Wrangler

1 Answer

5th. Gear


Sounds like you may have bent a shift fork or your cluster gear has some missing teeth on it now. I would venture to say that is it a bent shift fork. This will require the transmission be removed to gain access to inspect and repair.

Dec 06, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
1995 Jeep Wrangler Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...