Question about 2002 Ford Excursion

Open Question

2002 Excursion driver's side seat and pedals won't adjust.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: Ford drivers side heated seat doesn't work any ideas?

Most likely one of the heater elements in either the seat cushion or seat back is open.It leaves the module and goes to the seat back on the YE/LB wire thru the seat back and leaves there on the GY/LB wire and goes to the seat cushion and leaves there on the VT/LB. An open in either one of these will cause it not to work.Usally its the seat cushion one that goes bad.
You can test them with an ohm meter and you can get the heated element seperate. Just have to remove the cover to replace it.

Posted on Feb 17, 2009

Ad
jim9813
  • 124 Answers

SOURCE: 2004 Supercrew Lariat no driver power seat or pedal adjust

Maybe, you can diag yourself with a test light and an ohmmeter. These will cost less at sears than having a dealer diag it. Check fuse 109 in the cab, that's the fuse for the driver's seat module. If that fuse is ok, then check power at the module. It's a little black box under the driver's seat with i think 3 connectors. Back probe the dark green wire at the connector with a test light, you should have power, even with the key off. If not, repair the circuit. Clamp the test light to battery positive and back probe the black wire, if the light does not light, repair that ground circuit. Test the memory set switch by measuring with an ohmmeter points 7 and 2, 7 and 6, 7 and 5 resistance should be less than 5 ohms, if not replace it. If all these tests pass, disconnect the connectors from the module and give 12v to the red and white wire. If the seat moves, have the module replaced at the dealer, it will have to be programmed.

Posted on Aug 10, 2009

morse008
  • 1111 Answers

SOURCE: 2005 f150 lariat. Power windows, adjustable pedals

check all fuses and relays

Posted on Aug 23, 2009

Danniboi
  • 1098 Answers

SOURCE: My manual driver's side seat adjuster won't lock

Hi, you may have to remove the seat from the car it's most likely the only way you are going to be able to see the fault, the lever for lifting the seat is normally the cause have you tried forceing the lever back into position or working it up and down.

Th seat is pretty easy to take out, Regards

Dan

Posted on Feb 01, 2010

  • 6 Answers

SOURCE: seat belt won't retract complete, drivers side

have a look to see if its coiled in twisted as you pull the belt out if the buckle doesn't line straight to the female end well its probely retracted in twisted to repair pull the belt out all the way and then realign the belt its quite hard to do so take your time hope this helps.

Posted on Jun 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a way i can replace the front clip of a 2002 ford excursion with other truck parts


It looks like the F250 and Excursion use the same part number for the outer fender sheet metal. You can compare part numbers on the link shown and decide if it will work for you
2002 Ford Excursion Fender Replacement Front Driver Side Replacement...

Feb 01, 2015 | 2002 Ford Excursion

1 Answer

Comfort access failure.


Sounds like they might have missed plugging the door harness in to the body, or maybe left a ground unhooked.

Apr 24, 2013 | 2002 Ford Excursion

2 Answers

The drivers seat won't move and the heated seats won't work on both sides. Where is the fuse?


Check underneath the seat for an inline fuse. It is a glass type fuse in a fuse holder that you have to push and twist to get out.-----------------------------------------------------------------------------
XPROG-M

Apr 18, 2013 | 2006 Chevrolet Tahoe

1 Answer

The larger passenger seat won't lock


Be sure to inspect and clean the complete seat track, especially the locking lever. Hope this helps.

Jul 12, 2012 | 2002 Ford Excursion

3 Answers

2002 buick park avenue power drivers seat won't go up or down


The most common problem is the gear breaking under the seat. There is one motor to make the front go up and down and one motor to make the back go up and down. The front up/down motor is the easier one to replace. I have a video of one way to fix the up/down motors. I demo the back motor. Here is the link to my video: http://www.youtube.com/watch?v=wQLVvUf-9rs

Jun 30, 2012 | 2002 Buick Park Avenue

1 Answer

Where is the fuel pump inertia switch on a 2000 excursion?


driver's side kick panel beside the parking brake pedal.

Jun 09, 2012 | 2000 Ford Excursion

1 Answer

Why won't the driver's seat on my 2006 XJ8L won't adjust in height?


You have a problem with the power seat transmission. The 1st thing to do is make sure that nothing under the seat is impeding the movement of the seat, if that is OK you will need to try and find a used power seat transmission, the parts are not sold separately, just the whole assembly.

Feb 13, 2012 | Jaguar XJ8 Cars & Trucks

1 Answer

My 2002 Mazda Protege driver side seat belt receiver won't engage with the seat belt (it won't hold). Is there a warrenty form to have this fixed for free at the dealer


first try blowing it out with a air hose,, if that doesn't work, save yourself some money , and just grab one from a junk yard , there are no warranty statements that I could locate for your question

Sep 06, 2011 | 2002 Mazda Protege

1 Answer

What fuse is for the driver seat and pedals for 2002 excursion?


I use and I'd recommend you register for free at www.autozone.com Once registered you'll have access to repair and shop manuals for virtually any car or truck. All the data and diagrams, (including a diagram of the fuse panel), you need now or may need in the future will be a couple of mouse clicks away.

Jul 19, 2011 | 2002 Ford Excursion

2 Answers

I have a 2004 Chevy Silverado. The heated seat on the drivers side does not work. When you push the button to turn it on, the lights come on briefly then turn off.


Would you say it stays on about 30 seconds and does the passenger side do the same thing? If possible retrieving the codes will narrow down the search for a correct solution.If the passenger side is ok we may be able to eliminate the passenger side as bring part of the problem.Please advise so will know which way to go with your solution.


Condition/Concern:
Driver and passenger heated seats inoperative or shut off in 30 seconds. There will be DTCs B2435, B2440, B3606 and/or B1825 set in the Drivers Seat Module. The adjustable pedal position sensor, seat recliner position sensor and both heat seat thermistors share the same 5 volt reference internal to the Drivers Seat Module. A fault in any of these components/circuits can make the heated seats inoperative or shut off in 30 seconds, as well as, the seat recliner and/or adjustment pedals may move in short increments when operated. A fault in heated seats, adjustable pedal or seat recliner will affect BOTH heated seats.
Note:: Even if the vehicle is not equipped with adjustable pedals DTC B3606 still may set.


To help isolate the area of concern use the Tech 2 or a comparable scanner and go to "Sensor Data" in the Drivers Seat Module. Monitor the following parameters for being out of range:
Recline Position- Normal range .39V-4.58V
Pedal Position (if equipped) - Normal range .39V-4.58V
Psgr. Seat Heat Sensor- Normal range 1V-4V
Drvr. Seat Heat Sensor- Normal range 1V-4V
If a parameter is found to be out of range inspect circuits for any opens, shorts to ground, or voltage. If none found replace the suspect component.

Please be aware of the following common areas of concern:
  1. The adjustable pedal position sensor internally shorted pulling the 5 volt reference low. Disconnect the adjustable pedal position sensor and see if the heated seats start working correctly, if so replace. Note Important:: The APP (Accelerator Pedal Position) sensor is NOT the adjustable pedal position sensor. Make sure the correct sensor, adjustable pedal position sensor, is disconnected.
  2. The seat recliner position sensor internally shorted pulling the 5 volt reference low. Disconnect the recliner position sensor and see if heated seats start working correctly, if so replace.
  3. An open in either heated seat thermistor circuits (signal or low reference). The most common is the passenger thermistor where it passes through seat connector C305 pin "L" or "K" or C399 pins "R" or "G".
  4. A chaff to ground on either heated seat thermistor signal circuits. The most common is circuit 5475 black/red or dark blue shorted to ground in the passenger seat near the buckle. Note Important:: The heated seat thermistors act differently to "OPENS and SHORTS" than the adjustable pedal position sensor and seat recliner position sensor. The adjustable pedals and seat recliner sensors can be disconnected for testing of the heated seats. Where as the heated seat thermistor circuit must be working correctly before EITHER heated seat will operate. Disconnecting one thermistor, which may have a concern will not allow the opposite heated seat to work correctly, BOTH side must be operational before EITHER heated seat will operate.
Clearing DTCs
If DTCs will not clear when using the Tech 2 or comaparable scanner after a repair has been made, try operating the device in which the repair was made. Example, if a repair was made to the passenger heated seat thermistor circuit, the DTCs may not clear unless the passenger heated seat is operated.
Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

Nov 17, 2010 | 2004 Chevrolet Silverado 2500HD

Not finding what you are looking for?
2002 Ford Excursion Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...