Question about Ford F-250

1 Answer

Do I need to take off the exhust manifold off to get to the starter and remove it?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 273 Answers

NO!

Posted on May 18, 2011

Testimonial: "Sweet! Then that will be my first fix before I get on top of the nissan. You have been alot of help and reliving me of stress before bed lol! THX!!"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, my golf mk1 1.6 1995 model makes a tapping sound when i drive it but it stops when i idle


Sounds like to me a small exhust leak either
a exhust manafold gasket or exhust flange
gasket or cracked exhust manifold.
Anything else would be enteral meaning
valves need to be set, bad lifter, bad rod bearing,
bad oil pump, or timing chain tensioner,
BUT I would be willing to put my money
on an exhust leak or timing chain tensioner
it's one of the 2

Jun 29, 2014 | 2000 Volkswagen Beetle

1 Answer

Gas eaking from exhust manifold where it mou


tighten the bolts if the exhaust fumes still come out replace the gaskets if its gassolien your seeing there is a recall for the fuel rail

Feb 14, 2014 | 2001 Chrysler Town & Country

1 Answer

Gas keak at exhust manifold


remove the manifold from the engine and have it machined flat at an engineering shop . Fit new manifold gasket and tension the studs correctly in the correct order . Check the stud tensions as the innermost studs are tighter than the end studs .

Feb 14, 2014 | 2001 Chrysler Town & Country

1 Answer

I need torque specs for the intake manifold, heads and exhust manifolds on a 2000 ford tuarus


go to www. automecanico.com this web is in spanish however you can translate by your browser to english. is powerful

God bless you

Sep 18, 2012 | 2000 Ford Taurus

1 Answer

I need torque specks for valve train for a 1987 nissan truk v6 3.0 litter


cylinder head bolts 40 - 47 ft lbs, intake manifold bolts 12 - 14 ft lbs. , intake manifold nuts 17 - 20 ft lbs. , rocker arm shaft bolts 13 - 16 ft lbs. exhust manifold bolts 13 - 16 ft lbs. i hope this helps.

Dec 22, 2010 | Nissan Pickup Cars & Trucks

1 Answer

1996 4.3 w engine knock. Don't hear it cold unless rev engine. Can hear it best on pass side engine, on intake more than rocker cover. Gets much worse as engine warms up. Does this engine have a balance...


It sounds like you have a lifter that is sticking or the nut that holds the rocker arm has come loose. In eighter case you need to remove the valve cover to see if its the nut tightten to 20 ft lbs If its the lifter you can try to free it and make it move but to replace it you need to pull the head off Be sure this not an exhust that you are hearing they can sometimes sound similar especialy if the exhust manifold has a small crack in it. That can be repaired with out removeing the manifold

Dec 18, 2010 | 1996 GMC Jimmy

1 Answer

We're is a bank 1 sensors located on a 2002 isuzu axiom.


BANK ONE SENSOR IS UP STREAM ITS ON EXHUST MANIFOLD OR EXHUST PIPE BEFORE CAT CONVERTOR

Oct 11, 2010 | 2002 Isuzu Axiom

1 Answer

Finding the starter on 2005 nissan pathfinder


STARTER LOCATION ON 4.0 V6 -REMOVE ENGINE UNDER COVER.REMOVE EXHAUST MANIFOLD COVER FROM EXHAUST MANIFOLD RIGHT BANK TO GAIN ACCESS TO STARTER COVER BOLTS.THEN REMOVE STARTER COVER BOLTS AND REMOVE STARTER COVER.**** 5.6 V8 ENGINE YOU HAVE TO REMOVE INTAKE MANIFOLD TO GET TO THE STARTER.

Sep 10, 2010 | 2005 Nissan Pathfinder

2 Answers

How do i find where an exhust leak is coming


check where the headers come off of the engine exhaust leaks are generally quite loud and you will either be at the headers/exhaust manifold or just as you come off that bend there will be a flange gasket inside the two pipes joining. from the bend to the straight pipe just as it passes the gearbox and starts to straighten out.

Jun 22, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

Remove a starter on a chevy s-10 pu


no just the ones by the starter

Jan 19, 2009 | 1985 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...