Question about 2002 Chevrolet Impala

1 Answer

How do I remove the transmisson in a 02 chevy impalia do I have to drop the motor and sub frame

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 111 Answers

To remove the transmission the car has to be in the air 6 feet in the air at least and no u do not have to remove the engine but the transmission is very heavy and u need the right tools to do it. u have to remove the drive shaft its a lot of work.

Posted on May 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 chevy cavalier transmission how to take it out


you have to support the engine with an engine brace, drop the sub frame after all things connected to it are disconnected, then pull the drive axles, unbolt anything connected to the trans mission like lines, starter motor, unbolt flywheel to torque converter bolts and then transmission to engine bolts, then pull transmission from motor and drop out of car. go to the library and get a repair book on your car it will show you what has to be done then you can decide if this is a job you can handle.

Jul 28, 2015 | Cars & Trucks

1 Answer

How to lower front sub frame on 2002 mercury sable


support car place jack stands under sub frame. using an engine support to hold motor in place, disconnect anything that is attached to sub frame, ex: motor mounts. then unbolt sub frame bolts(4) and raise car to remove sub frame. note sub frame is heavy.

Jun 24, 2015 | Mercury Cars & Trucks

1 Answer

How to put a alternator 1997 cadillac deville


Basic hand tools

Are you asking how to access
a transverse motor?

From the bottom & thru the fender
around the sub frame

Hopefully you won't have to drop one
side of sub frame to get it off

Mar 07, 2013 | 1997 Cadillac DeVille

2 Answers

How do I remove Power Steering Rack on my Ford


cross member yes you do haveto remove it

May 01, 2010 | 2003 Ford Focus

1 Answer

2002 pontiac grand am rack and pinion replacement how to


Removing the rack and pinion assembly from a 2002 Pontiac Grand Am Se To get the old rack and pinion off of the car for replacement involves lowering the sub-frame, removing the stabilizer bar, and pulling the rack out from the driver side of the vehicle.
  • Start by lifting or jacking up the car and removing the front wheels. Once the car is safely supported, disconnect both tie rods from the steering knuckles.
  • The rear motor mount sits on top of the cross-member part of the sub-frame, and must be disconnected to allow the sub-frame to drop a few inches. Remove the three bolts attaching it to the center of the sub-frame - one in the back and two in the front near the back of the transmission.
  • Loosen the two bolts holding the front of the sub-frame. Place a scissor jack or bottle jack under the rear of the sub-frame where the bolt for the motor mount was. Remove the two smaller bolts from each side of the rear of the sub-frame (total 4 bolts) and then loosen the two remaining larger bolts holding the rear of the sub-frame (these bolts go through the rear control arm bushings and are very long) until the bolts are only going through the control arm bushing, and not into the chassis. You do not need to remove these completely.
  • Remove the stabilizer links from both sides.
  • Next you must disconnect the steering linkage. This is done easily by lifting up the rubber boot to expose the small bolt holding the linkage. Remove the bolt and pry the linkage upward using a pry tool or screw driver.
  • Near the passenger side of the crossmember, remove the bolt holding the power steering line bracket to the chassis. You may now begin to lower the sub-frame using the jack. The front bolts should have lowered the sub-frame about a half-inch or so, allowing you to lower the back of the sub-frame 3 or 4 inches.
  • With the sub-frame lowered, you can now access the bolts holding the stabilizer bar in place. The right side has a nut screwed onto the top of it holding the power steering lines, remove this first, then remove both bolts. Pry or pull the stabilizer brackets up and out. Remove the stabilizer bar.
  • Now you can get to both of the bolts holding the rack in place. Remove both of these, then begin to slide the rack toward the driver side wheel well until there is no more slack in the power steering lines. At this point you should be able to get to the nuts securing the lines on the rack. Loosen both nuts and be ready with something to cap the ends with. I used part of a plastic bag and a wire to tie it. You can now pull the rack out through the driver side.
  • Be sure to replace the rubber o-rings on the ends of the lines when putting the new rack in. Replace everything in the reverse order. Put your tie rods on the new rack, making sure to count the turns or make a mark or measure to be sure your tie rods end up close to the same length as before.
  • Bleed the power steering system.

Important: Get an alignment! Not only is it dangerous to drive with your steering out of align but it will also grate the tread off your tires in a matter of weeks or even days.

Oct 27, 2009 | 2002 Pontiac Grand Am

1 Answer

I cracked my oil pan and i need to know if i need to take out my engin to change it i'm low on cash i need help


here's v6 3.8L

Section 03-01A: Engine, 3.8L 1996 Thunderbird, Cougar Workshop Manual
IN-VEHICLE SERVICE Oil Pan/Oil Pump Screen Cover and Tube Removal
  1. Disconnect battery ground cable (14301).
  1. Remove air cleaner outlet tube (9B659). Refer to Section 03-12 .
  1. Remove two bolts retaining radiator upper sight shield (8C291) and position radiator upper sight shield aside.
  1. Remove hood weather seal.
  1. Remove windshield wipers.
  1. Remove LH cowl vent screen and wiper module.
  1. Install Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Remove front engine support insulator through-bolts.
  1. Partially lower vehicle.
  1. Raise engine and support with Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle.
  1. Remove starter motor (11002).
  1. Position drain pan.
  1. Drain engine oil.
  1. Remove oil bypass filter (6714).
  1. Remove starter motor wire, ground strap and automatic transmission oil cooler lines.
  1. Remove oil pan-to-bell housing bolts and bolts at crankshaft position sensor lower shield.
  1. Remove remaining oil pan retaining bolts.
  1. Remove steering shaft pinch bolt and separate steering shaft.
  1. Position transmission jack under front sub-frame (5C145).
  1. Remove six rearward bolts on front sub-frame. Loosen two forward front sub-frame bolts.
  1. Remove lower shock absorber-to-front suspension lower arm bolts and nuts (both sides).
  1. Lower front sub-frame.
  1. Remove oil pan (6675).
  1. Empty any residual oil from oil pan.
  1. Remove oil pump screen cover and tube retainer bolts and support bracket nut. Remove oil pump screen cover and tube (6622) and discard oil pump inlet tube gasket (6626).

Apr 14, 2009 | 1996 Ford Thunderbird LX

1 Answer

Auto trans 4x4


Oh lord, are you in for some work. First of all you will need a transmission jack, a must and a couple of strong guys if you don't have a lift. First things first. Disconnect neg. bat. cable. Raise up on jack stands. Disconnect drive shafts and tape bearings caps on drive shafts. Remove Starter. Disconnect wiring harness plugs from transmission and transfer case. The wiring harness connection on the shift linkage does not remove. There are 2 connectors and are glued at factory. Remove whole shift linkage unit from side of trans. Remove exhaust. Remove dust cover. Mark spot on flywheel and tourque converter, then remove bolts from flywheel. Support trans. with jack. Remove transfer case bolts from trans. Remove mount nuts from transfer case bolts. Remove bell housing bolts from motor to trans. Remove bolts from crossover support for transfer case mount from the main frame. Raise up transmission and remove crossover support. One guy now supports transfer case and other works transfer case loose. The transfer has to be jockeyed around until it drops out. It will not come straight out or down because of the tor. bar support frame. It has to be wiggled out and down. Guy supporting transfer case gets trans fluid bath and this is all muscle work. With transfer case out, put another jack under motor for support or risk breaking motor mounts and other things. Slide transmission back and lower down and its free, It is a very dirty, oily, nasty hard job. I just went through it. I wouldn't do it again. If you can afford it, take it to a pro. Well worth it. Remember once started, your pretty much commited. Reverse the whole thing to install. Good Luck

Feb 01, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2002 Jaguar X-Type Oil Pan Gasket replacement


have you smashed the sump ??never seen one leak yet?? sure its not the front or rear end oil seals ??..sounds like you have the sub frame in the way ,evan if you remove this bolt you will not be able to drop the sump without removing or lowering the sub frame assembly as the oil pick up pipe stops you from removing the sump in situe.Its not difficult to drop sub frame just time consuming

Jan 01, 2009 | 2002 Jaguar X-Type

Not finding what you are looking for?
2002 Chevrolet Impala Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...