Question about Jeep Grand Cherokee

1 Answer

Looking for location of cam position sensors in 2002 4.7 grand cherokee

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 273 Answers

The CAMshaft position sensor on the v-8 4.7 liter engine is on the front right side (passenger) of the engine bank.

The CRANKshaft sensor is behine the stater motor on the passenger side


looking for location of cam - 2010-07-20_234719_s118.gif
Hope this helps, PLEASE RATE!!! James Booth :)

Posted on May 18, 2011

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

  • 6982 Answers

SOURCE: Where do I locate the Crankshaft Position Sensor

Crank sensor is generally located on the bellhousing 11 o'clock position looking from the rear. It is always even with the flywheel as it gets it's trigger from that.
It is not easy to reach it but it is not impossible to do. If yours has spacers, remember that it is better to use too many than not enough (too close to the flywheel and it will self-destruct) it can pick up a signal nearly 1/4" away from wheel though. Since it's not easy to change, make sure you test it before you decide to replace it though!

Posted on Oct 24, 2009

  • 2926 Answers

SOURCE: where is the cam shaft

What size is the engine?

Posted on Dec 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft position sensor on a 1997 Bravada?


most cars its on the end of the cam.
you didnt post vin or engine option so can say.
but the cam has a sensor. that tells the ECU where #1 cylinder is.
is car a bravada or a jeep grand cherokee. , impossible to tell.
PointsProblem with 1997 Jeep Grand Cherokee Where is the camshaft position sensor on a 1997

Oct 25, 2013 | 1997 Jeep Grand Cherokee

1 Answer

How do i set the timing on a 2002 jeep grand cherokee laredo 6 cyl?


Your timing is locked. (distributor is installed with no adjustment feature... on 02's you may not even have a distributor as it's replaced by the cam sensor) All timing and fuel mixture is controlled by the engine computer. Main inputs to the computer that influence changes are the throttle position sensor and MAP sensor but all sensor inputs are evaluated.

Apr 21, 2011 | 2002 Jeep Grand Cherokee

1 Answer

Location of cam sensor 2003 jeep grand cherokee v8


Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Jul 21, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Where is the cam sensor for a 2004 Jeep grand Cherokee 4.7 HO


The can sensor in most cases is located in the below mentioned position.The camshaft position sensor is located just above the oil filter on the right side (sitting in the vehicle) of the engine. But if in case you don't find the sensor there then,
In some model of jeep its located on the BELL housing. ON bell housing to locate the cam sensor:-- AS you stand in front of your JEEP .Head under the bonnet .Then exactly on the right side you will see a fuel rail .Follow the fuel rail and you will reach the bulk head. The can sensor is down there ON THE TOP OF THE BELL HOUSING.
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Jun 12, 2010 | 2004 Jeep Grand Cherokee

1 Answer

My Grand cherokee 4.7 1999 does not run the engine


Likely the sensor involved is the crank position sensor, next in line would be the cam sensor. You could also have a bad fuel pump or pump relay. Crank sensor is on the bellhousing at about 11 o'clock looking from the rear. It is even with the position of the flywheel. cam sensor is inside or is your distributor, depending upon your system. All are expensive so I recommend that you run some tests outlined in haynes, chiltons or other decent repair manuals before changing anything.

Jan 28, 2010 | 1999 Jeep Grand Cherokee

2 Answers

Where is locate the camshaft position sensor on 2001 jeep grand cherokee laredo limited 4.7 l


The camshaft position sensor is located inside the distributor. It is a hall effect swich, simply remove the distributor cap and the rotor and you can lift it out, unplug and replace.
Have fun but beware a bad crankshaft position sensor can cause a false cam sensor code to be set sometimes.
Good luck.

Dec 05, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Where do I locate the Crankshaft Position Sensor on 2002 Jeep Grand Cherokee 4.0L? Can I change it myself?


Crank sensor is generally located on the bellhousing 11 o'clock position looking from the rear. It is always even with the flywheel as it gets it's trigger from that.
It is not easy to reach it but it is not impossible to do. If yours has spacers, remember that it is better to use too many than not enough (too close to the flywheel and it will self-destruct) it can pick up a signal nearly 1/4" away from wheel though. Since it's not easy to change, make sure you test it before you decide to replace it though!

Oct 24, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Location of crankshaft position sensor Jeep grand cherokee 1997


left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Jun 13, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...