Question about Ford Crown Victoria

1 Answer

Which way do you turn the bolt on a 98 crown victoria harmonic balancer pully

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 273 Answers

To the left to loosen it and to the right to tighten it

Posted on May 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Autodata manuals


Timing mark/knotch is on the harmonic balancer that the pully bolts to on crankshaft.Mark said notch with a white paint pen and line it up with proper mark on tab bolted to block at the harmonic balancer.

May 09, 2014 | 2002 Mitsubishi Colt

1 Answer

The big outside pulley on the harmonic balancer fell off


The Harmonic balancer is held on to the front of the crank shaft with a bolt. there are pullys pressed onto the harmonic balancer in rubber.If more pulleys are needed for more accessories they are bolted to the harmonic balancer.

Apr 20, 2013 | Cars & Trucks

1 Answer

What all has to be replaced when the crankshaft pulley? falls off


Did the crankshaft pulley separate from the harmonic balancer? No bolts missing? This happens once in a while. Just replace the harmonic balancer assembly (and probably the belt).

Jun 02, 2012 | 1999 Ford Crown Victoria

2 Answers

Location of crankshaft censer 2007 chevy cobalt


The Crank shift sensor is located in front of the motor in between the intake manifold and oil filter housing, nest to the knock sensor. Look on side cylinder block beside starter.you have to remove the starter to remove the crankshaft sensor. Hope this helps. Thanks for choosing Fixya, RJ

May 16, 2011 | 2007 Chevrolet Cobalt Coupe

1 Answer

How can i fix my locked up engine in my 1987 crown victoria? i had oil in it and to my knowledge my starter was good. what route should i take next?


Try taking out the spark plugs put motor oil in all cylinders and let it sit for a day or 2 fully charge the batterry for the 2 days on (2 amp if possible) try it again a few times if it still won't free up use a socket on a breaker bar on the harmonic balancer bolt and try to turn it manually...Good Luck

Jul 06, 2010 | 1987 Ford Crown Victoria

3 Answers

Pully disconnected from harmonic balancer. Trying


thats a hard bolt to break lose almost takes the sudden **** u get for a impact.i had to use a guy bigger then superman to break it free for me

Oct 04, 2009 | 2000 Lexus SC

1 Answer

Need specs on bolt through the harmonic balancer....which way do you turn too remove bolt ?


normal thread,righty tighty,lefty loosey,an air impact would work great,hope this helps

Sep 05, 2009 | 2001 Ford Crown Victoria

1 Answer

Pulling the harmonic balancer off a 98 nissan pathfinder


Most balancers have two parts, the inner crankshaft section is where the huge bolt is and holds it to the crankshaft, they may also be a few smaller bolts around the outside of the big bolt, those hold the belt pulley on to the crankshaft. If it thats kind of setup remove the small bolts and the pulley should come off, you may need to use a wooden hammer etc to get it loose once the bolts are out.

Mar 11, 2009 | 1998 Nissan Pathfinder

1 Answer

How do you set the timing on a 1997 ford crown victoria?


You can not set timing on 97 CV. It is computer controlled. It does not have a distributor the PCM (computer) uses a signal from the crankshaft postion sensor mounted near the harmonic balancer to control timing.

Jan 19, 2009 | 2005 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...