Question about 2000 Suzuki Grand Vitara

Open Question

Replace cv joint and axle bushing on 1999 suzuki grand vitara

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Nitrotrike
  • 589 Answers

SOURCE: CV joint replacement

Generally no tool is required. If you use a "pickle fork" you will risk damaging the dust boot.

Have you tried whacking the spindle right near where the ball joint stud comes through? This will take a few good shots to break it loose.

Be careful not to hit the threads!

Posted on Jun 25, 2008

2tone2
  • 7 Answers

SOURCE: what is the procedure to

You don't need the special tools that they use in this procedure, you can use a hammer and a block of wood to get the axle out of the hub and you can use a pry bar to get the axle out of the transmisson.



Notice: Care must be exercised to prevent the constant-velocity joints from being over-extended. When either end of the drive axle is disconnected, over-extension of the joint could result in separation of internal components and possible joint failure. Drive axle joints and seals should be protected any time service is performed on or near the drive axles. Failure to observe this can result in interior joint or seal damage and possible joint failure.
Notice: Prior to removal of drive axle assembly, cover all sharp edges in the area of the drive axle with shop towels so that the seal is not damaged during removal.
Removal Procedure

  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Place shop towels underneath the outer joint to protect from any sharp edges.

  4. 141983.gif
    tif.gif
  5. Insert a drift (1) into the caliper and the rotor to prevent the rotor from turning.
  6. Remove the drive axle nut (2) and the washer.
  7. Remove the lower ball join from the steering knuckle. Refer to Lower Control Arm Ball Joint Replacement in Front Suspension. If you remove the right axle, turn the wheel to the left. If you remove the left axle, turn the wheel to the right.
  8. Disconnect the wheel speed speed sensor harness. Refer to Wheel Speed Sensor Replacement in Antilock Brake System.
  9. Disconnect the stabilizer link from the lower control arm. Refer to Stabilizer Shaft Link Replacement in Front Suspension.

  10. 442393.gif
    tif.gif
  11. Use the J 28733-B in order to disengage the axle from the hub and the bearing.
  12. Separate the hub and the bearing assembly from the drive axle. Move the strut and the knuckle assembly rearward.

  13. 500285.gif
    tif.gif
  14. Remove the inner joint from the transaxle using J 33008 attached to J 29794 and J 2619-01 for the intermediate shaft, if equipped.
Installation Procedure Notice: Prior to installation of drive axle assembly, cover all sharp edges in the area of the drive axle with shop towels so that the seal is not damaged during installation.
Any time the front halfshaft is removed, the transmission (the halfshaft male and female shank) and the knuckle sealing surfaces should be inspected for debris or corrosion.
If debris or corrosion are present on the sealing surfaces, clean them with a 320 grit cloth or equivalent. Transmission fluid may be used to clean off any of the remaining debris. The surface should be wiped dry, and the halfshaft should be reinstalled free of any debris or corrosion buildup.

    189013.gif
    tif.gif
  1. Install the drive axle (2) into the transaxle (1). Place a non-ferrous drift into the groove on the joint housing and then tap until the drift is seated. Be careful not to damage the axle seal or dislodge the seal garter spring when you install the axle.

  2. 442471.gif
    tif.gif
    Important: Verify that the drive axle is seated by grasping on the inner joint housing and pulling outboard.
  3. Install the drive axle (1) into the hub and bearing assembly (2).
  4. Install the stabilizer link. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
  5. Connect the wheel speed sensor harness. Refer to Wheel Speed Sensor Replacement in Antilock Brake System.
  6. Install the lower ball joint to the steering knuckle. Refer to Lower Control Arm Ball Joint Replacement in Front Suspension.

  7. 141983.gif
    tif.gif
    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  8. Install the washer and the new drive axle nut (2).
  9. Insert a drift (1) into the caliper and the rotor in order to prevent the rotor from turning.
    Tighten
    Tighten the drive axle nut to 200 N·m (144 lb ft).
  10. Install the tire and the wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  11. Lower the vehicle

Posted on Nov 02, 2008

  • 10 Answers

SOURCE: where is the starter for a 2000 suzuki grand vitara located

starters are normally located at the rear of the motor usually hard to get too or see. should be on your bell housing in other words just in front of the gearbox/clutch

Posted on Dec 23, 2008

  • 507 Answers

SOURCE: average repair cost for cv joint or axle replacement

Average time should be around 2-3 hours. Every shop charges different hourly rates. Dealerships will be around at least 80 an hour, smaller shops will run lower.

Posted on Jan 05, 2009

  • 2 Answers

SOURCE: Suzuki wiring diagram

http://www.suzuki-club.ru/forum/downloads.php?do=cat&id=5

Posted on Jun 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front right axel 2001 4wd suzukoi grand vitira


RTM, Read the manual.?
called FSM
its just 4 bucks. or at alldata.com for 15, 1yr

https://suzukipitstopplus.com/Products/1191-2001-vitara-grand-vitara-service-manual.aspx


cv's bad ?
https://www.youtube.com/watch?v=LV0qc4R6vqI

and many more there
now google.

type
grand vitara c/v joints

and magic happens






Jun 22, 2014 | 2001 Suzuki Grand Vitara

1 Answer

I have a 2001 Suzuki Grand Vitara. The passanger side cv axle will not break free from the transaxle casing. Any suggestions?


alldata dot com

its all there, every step.

yes, RTM, CV service has many pit falls, why not read the steps
and warnings.?

Sep 27, 2013 | 2001 Suzuki Grand Vitara

1 Answer

Can you conver front axel u joint type to a cv joint type on an 95 jeep grand charokee lorado


I owned a 93 GC 4x4 and I did replace my front axles with CV joint axles. The new axles came with CV joints, with a rubber boot and all so yes you can.

Sep 09, 2012 | 1995 Jeep Grand Cherokee

1 Answer

How do i change the rear axle seal on a 1999 grand vitara


how do i remove the axle seals on a 1999 suzuki grand vitara

Mar 02, 2010 | 1999 Suzuki Grand Vitara

1 Answer

2002 silverado Z71 4x4 front cv axle broke


sounds like you have to much angle on your cv joint there should be no more then 30% on your cv joint might have to reconfigure your lift

Sep 19, 2009 | 1999 Suzuki Grand Vitara

2 Answers

Popping sound when turning. axle looks good. no leaks. could it be the wheel bearing?


Could be the bearing..

Is it a clicking sound ??
If so - could be a CV joint..

Check all the CV boots (the rubber covers over the CV joints)..

Push on them looking for splits,, seperatiob or cracks.. If you see anything like that -rest assured you have a CV joint problem..

If boots go bad & are replaced in time (& CV joints greased) they can be saved.. If it has been too long - the joint will need to be replaed too..

Hope this helps !!
Please rate me good ;o)

Jul 12, 2009 | 1999 Suzuki Vitara

2 Answers

1999 Suzuki Grand Vitara Vibrate/shake at 55-70 mph


Lift the back of your car.With a stable rest and with the two hind wheels hanging, run your car up to the speed where you experienced vibration. have someone take care of the throttle and shifting while you observe the transmission shaft. You may have an imbalanced shaft.

May 12, 2009 | 1999 Suzuki Grand Vitara

2 Answers

Cv joint


Loosening but not removing the strut top mounts and sway barend link bushings can provide a bit more suspension travel for easieraxle removal. ccr20051001cv_s04.jpg
Loosen and remove wheel side axle mounting bolts. ccr20051001cv_s05.jpg
Separate the axle from the wheel. Do not allow axle to hang from thetransmission or differential. Oil seals could be damaged. ccr20051001cv_s06.jpg
Gently pull, pry, or otherwise liberate the axle from the transmissionor differential. Do not bend axle seals. Be careful not to teartransmission or differential oil seals. ccr20051001cv_s07.jpg
The axle splines on the right show damage. Note the c-clip on both axles. ccr20051001cv_s08.jpg
Don't forget to transfer any axle seals, ABS rings, or other parts to the replacement axles. ccr20051001cv_s09.jpg
Guide the replacement axle into place. Depending on the type of retainer, the axle should click firmly in place. ccr20051001cv_s10.jpg
Always use the proper torque on the axle bolts. Check axle rotation. Reassemble dismantled components.

May 09, 2009 | Suzuki Esteem Cars & Trucks

1 Answer

Can I just replace just one cv joint


Yes you can,I'm not sure if your refering to the whole axle or one cv joint on the axle.Replacing a cv joint is best left to a qualified mechanic,most cv joints require special tools and procedures to replace correctly.

Apr 22, 2009 | 2000 Suzuki Esteem

Not finding what you are looking for?
2000 Suzuki Grand Vitara Logo

Related Topics:

844 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...