Question about 2002 Hyundai Santa Fe

1 Answer

2002 sante fe; new front calibers, brake pads and rotors. bled the front calibers; fluid came out, refilled reservoir. brake is hard when car is off. when car is on the brake goes to the floor. how can i solve this problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 92 Answers

Probably you have to bleed the master .couse seem to me till air on the brake lines

Posted on May 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change front brake pads


need to know the make and model. but on the average you need to pull the brakes off the rotor usually held on with 2 bolts on the rear of the brake housing. open brake fluid reservoir and squeeze the pads as far as you can (this can be done a big set of channel lock pliers or a big set of vise grips, just remember to put something on the caliber to protect it from gouging or damage) into the brake housing before installing new pads or they will not fit bad over the rotor. the pads usually just slide in or out and snap in place.

Apr 10, 2016 | Cars & Trucks

1 Answer

2003 s type brake front pad - what tools are need to change the pads


the front pads are pretty straight forward,just a c clamp is sufficient to press the calibers,make sure the brake fluid reservoir cap is off when you do them..just unbolt the calibers from the rotors and they work the same as standard brakes,but the rear calibers at time will need a caliber tool to turn and press the piston simultaneously

Sep 03, 2011 | 2006 Jaguar X-Type

1 Answer

How to change front brake pads


the front brakes are straight forward, open the brake fluid reservior,remove tires,then the caliber,then remove pads and use a c-clamp to compress the calibers,,install new pads,,the reinstall the cap on the fluid reservoir,when you crank the car,pump the brakes three times and on the last pump hold the paddle to floor then pull the electronic park brake. you will hear the module reset....

Oct 04, 2010 | 2006 Jaguar XJ8

1 Answer

How do you replace the front and rear brakes in a 2003 pontiac Grand Prix


Removal & Installation Front To Remove:
  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the bottom brake caliper pin bolt.
  5. Pivot the brake caliper body upward and secure out of the way. Do NOT disconnect the hydraulic brake flexible hose from the caliper.
  6. Compress the piston back into the bore using a C-clamp. Figure of brake assembly with caliper raised showing brake pads in mounting bracket gmpc_l4.gif

  7. Remove the inboard and outboard brake pads from the brake caliper bracket.
To Install:
  1. Install the brake pad retainers and both brake pads into the caliper bracket.
  2. Pivot the brake caliper down over the brake pads and into the brake caliper bracket. Insert the lower brake caliper pin bolt and torque bolt to 70 ft-lb. (95 Nm).
  3. Reinstall the tire and wheel assembly.
  4. Lower the vehicle.
  5. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  6. Check the master cylinder level and add fluid as necessary.
Rear To Remove:
Rear disc pads R&I gm-09-00-492.gif

  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the upper caliper mounting bolt.
  5. Pivot the caliper down to access the pads.
  6. Remove the inboard and outboard pads from the caliper bracket.
  7. Remove the brake pad clips from the caliper bracket.
  8. Compress the piston back into the bore using a C-clamp and the old inner pad.
To Install:
  1. Install new brake clips in the caliper bracket.
  2. Install the inboard and outboard pads in the caliper bracket.
  3. Pivot the caliper up over the pads.
  4. Reinstall the upper mounting bolt and tighten to 32 ft. lbs. (44 Nm).
  5. Remove the 2 wheel nuts securing the rotor.
  6. Reinstall the tire and wheel assembly.
  7. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  8. Check the master cylinder level and add fluid as necessary.
prev.gif next.gif

Aug 26, 2010 | 2003 Pontiac Grand Prix

1 Answer

What is minimum thickness on front rotor for 2004 sante fe and are ceramic pads required


1/8th inch pad thickness.discs if undercut by more than 1/32nd must be scrapped.they are so cheap anyway.......buy new.

Mar 06, 2010 | 2002 Hyundai Santa Fe

1 Answer

How to replace brake pads on 2006 oddesey


Raise and secure on stands after breaking loose the lug nuts and parking brake on for front pads.. Remove wheels and spread old pads back to push cylinders back in their bores on calibers to allow for thickness of new pads. Remove the 2 sliding claiber retaining bolts and rotate caliber out of mount and secure with wire, boungie cord, or rope to take weight of caliber brake hose. Remove old pads, install new, and reassemble in reverse order. Lugs on alloy wheel should be torgued to 95 foot lbs. Block front wheels, release parking brake,and do the back ones the same way. After completing, pump brake pedal slowly several times to seat new pads. If you move the MPV without pumping first, you will have no brakes to stop. If brake fluid level is high in master cylinder, you will need to take some out first to make room for returning fluid from caliber pistons being returned to their bores prior to any brake work. Rotors should be replaced or turned if scored or warped to have better clapping of pads to rotor surface.

Dec 12, 2009 | 2006 Honda Odyssey

1 Answer

Hyundai sante fe


My daughter has one . she has had it for 6 years the only thing she has done is put front brakes and rotors.

Jan 08, 2009 | Hyundai Santa Fe Cars & Trucks

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

Related Topics:

446 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...