Question about Chevrolet Blazer

1 Answer

What setting should the distributor be for a 2001 chevy blazer be

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 273 Answers

Book shows that this dist rotor is to be set pointing at #6 that is stamped into dist housing with @ 1 tdc compression. Hope this helps, James Booth

Posted on May 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Installed distib but its poping and sputtering in a 2001 blazer marks where lined up also and was on the number 6


Make sure the firing order is correct. I think this link will work:

http://www.carrestorationshop.com/2001_chevrolet_blazer/q2850542-firing_order_2001_blazer_lt

Aug 02, 2016 | 2001 Chevrolet Blazer

2 Answers

What would cause a 2001 chevy blazer to not start? we replaced sterring column and it acts like its not getting gas turns over to start but wont start what could be the problem? would the the brain ne


The ECM does not recognize the different key. A tool referred to as a Tech-2 plugs in to the scan port, the truck is put in learn mode and the prompts on the tool are followed, this "programs" the ECM recognize the new key.

Dec 02, 2014 | 2001 Chevrolet Blazer

1 Answer

How do I time a 2001 Chevy Blazer ZR2 4.3L? Why is it throwing codes in my 01 Chevy Blazer ZR2 4.3L for crankshaft and camshaft sensors?


was the distributor move, sometimes the rotor in the distributor will move just a hair. turn the motor by hand to tdc and see where the rotor is pointing

Oct 29, 2012 | 2002 Chevrolet Blazer

1 Answer

How to set timing on a 1997 chevy blazer and get a diagram of it


sorry but the ignition timing is controlled by the electronic control module, (ecm) however if you have a scanner that can read datastream you can adjust the cam ******.. go to cam ****** on the datastream list , start engine rev to 1200-1500 rpm and check reading should be at 0 degrees plus or minus 2 degrees, if not you adjust at the distributor by rotating the distributor. the adjustment should be made with engine off then restart and rev again to 1200-1500 rpm and check the cam ****** again,by the way if unable to adjust the distributor gear of the distributor itself may be worn out and need replacement, hope this helps.

(this info is for the blazer)

May 04, 2011 | 2001 Chevrolet Cavalier

1 Answer

I have a 2001 chevy blazer. after having a head gasket put on it will only run 180% out of time


Was the distributor put in backwards? (180 degrees out?)
Turn the crank to TDC, (drivers side front piston, or #1, should be going up, as it will push air on it's way. Then see if the distributor is pointing to the #1 wire.

Aug 12, 2010 | 2001 Chevrolet Tahoe

2 Answers

I have a 94 s10 blazer 4.3 and I had to remove the distributor but never marked it so now the timing is messed up. The distributor dose not have a #6 alignment mark so I cant get it working right. How do I...


Remove cylinder # 1 spark plug, # 1 is the front one on drives side, turn crankshaft pulley to TDC on compression stroke, you'll feel the comperssion at cylinder #1 spark plug hole, follow cylinder # 1 spark plug wire to distributor cap, mark outer part of distributor where # 1 sits, remove distributor and restabe distributor with rotor at mark you made, then set timing.

Jan 22, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

Where is the camshaft position sensor located on a 2001 chevy blazer


Also know as Distributor pick up assembly sit inside your distributor.

Jan 07, 2010 | Chevrolet Chevy Cars & Trucks

2 Answers

2002 chevy blazer won't start when it is cold/damp outside. Fuel pump repaced 3 times in a year. What could causing this?Starts fine when weather is nice.


could be a defective distributor cap(crack in it allows moisture in...moisture displaces the spark from where it needs to go).
You could try to replace the distributor cap and rotor.

Aug 30, 2009 | Chevrolet Blazer Cars & Trucks

2 Answers

Intalling distributor in 2001 chevy blazer


remove the distributor cap mark the position of the rotor on the distributor mark the position of the distributor on the intake or fire wall remove the hold down bolt and slowly remove the old one make sure the gasket comes off too to install just reverse the steps lining up the marks you made

Mar 01, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...