Question about 2006 Jeep Commander

1 Answer

2006 jeep commander rear caliper bolt torque specifications?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,140 Answers

Here you go2006 jeep commander rear caliper bolt torque - bonedivers_9.gif

Posted on May 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the torque specifications for front and rear caliper bolts for a Buick Lacrossee.


According to GM... Ft caliper pin bolts 70 ft lbs, bracket bolts 133 lbs ft. Rears are...caliper bolts 25 lbs ft, bracket bolts 89 lbs ft

Jul 03, 2017 | Buick Cars & Trucks

2 Answers

3.9l V6. Can I re-torque rear caliper bolts to 26 ft. lbs.?


you could but at this point I would just leave them alone unless there is a problem in the function of the calipers in which case remove and replace the bolts with new bolts as the used bolts will be stretched

Mar 02, 2016 | 2006 Chevrolet Chevrolet Impala LT

1 Answer

Brake caliper torque setting


the caliper to knuckle bolts? front or rear. my gawd,
its in the FSM.
the WK is here.
read it?
see chapter called brakes. its all there, every step.


http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

RTM,
ok , page 379
side pins 18 (f and R)
front caliper anchor bolts are 125 (foot/pound)

Jul 01, 2015 | 2010 Jeep Commander

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

What are the torque specs for the rear caliper bolts on a 2006 ram 2500 diesel?


the caliper bolt torque is 22 ft. lbs. thanks and come again

Mar 25, 2010 | 2006 Dodge Ram 2500

1 Answer

Torque for pyutting new rear brakes and rotors on a 2006 Town&Cou


Caliper mounting bracket bolts 125 ft, Caliper guide pins/bolts 26 ft, Brake hose to caliper 35 ft. Wheel lug nuts 100 ft. Wheel speed sensor 115in lbs*** This is for disc rear brakes Teves system. You do know that the rear disc is a Rotor/Drum. The parking brake shoes ride on the inside.

Jan 22, 2010 | 2006 Chrysler Town & Country

1 Answer

Torque setting for brake caliper mounting bracket


according to manual,
front caliper mounting bolts are 11 ft lbs
rear caliper mounting bolts are 220 inch lbs.

Jul 02, 2009 | 2005 Jeep Liberty

1 Answer

Jeep Commander Rear Brake Pad Installation


Per Chilton Auto repair manual:

Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

May 17, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2006 Jeep Commander Logo

Related Topics:

531 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...