Question about Buick Regal

1 Answer

I have replaced the driver side front wheel bearings 3 times in 6 months. the last time it went out within only 3 weeks. need help.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,140 Answers

Bad part? not properly installed?

Posted on May 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear wheel bearing still grinding after spindle shaft and wheels bearings were replaced


you could have a new defective part is what it sounds like to me.hope this helps

Mar 29, 2014 | 2003 Kia Rio

1 Answer

Very loud howling noise coming from front driver's side; replaced the wheel bearing 3 times within a month, and the problem is still there.


Have you checked you tire closely.Change it with the one on the other side and see if the sound transfer to that side.

Aug 24, 2012 | Cars & Trucks

2 Answers

Driver side wheel bearing problems.


Torquing might be the problem.
If they are tapered bearings, you should snug them down then back the nut off a quarter turn or so. I usually turn the nut back until the locking pin will align with the hole in the spindle.

Jul 11, 2012 | Ford Cars & Trucks

1 Answer

I have a 1997 Mercury Mountaineer. While driving STRAIGHT, not turning...there is a horrible grinding/rubbing sound coming from the driver side front tire. I had the wheel bearing replaced on the...


If its not the bearing and your Mercury is front wheel drive, it could be the "CV" joints.
It could be both....

Is the wheel rubbing the brake caliper?

Is something like the wheel well liner rubbing the tire(airflow pushing it into tire)?

Jack the tire off the ground and rotate it by hand. Push in & out at the top, sides, and bottom of the tire. Little or no play is considered acceptable. If you get a "clunking" sound and/or a lot of play the bearing(s) are bad. (If front wheel drive, chock rear tires, put transmission in neutral so you can rotate tire.)

Hope this helps.

Aug 06, 2011 | Mercury Mountaineer Cars & Trucks

1 Answer

I have a 2006 Scion TC that the right axle bearing went on last week and the shaft pulled out of the tranny. I replaced it with a remanufactured one from Napa last week and last night the same thing...


even when you buy from napa ,auto zone - checkers- all parts are manufactured from same place, I replaced the front wheel bearings in my 07 tc and with in a month they went bad had to replace them again, used a better bearing than what was the manufacture specs, so it could be bad workmanship or bad products, no every part is made to last .

Feb 16, 2011 | 2006 Scion tC

2 Answers

2004 Kias Sedona. I have the replaced the Front Wheel Bearing (Passenger Side) 4 Times in the last 6 months. The last one lasted 2 Days. It was sluggish going uphill, jerking, and then there was a loud...


My guess is the original shim that came with the factory bearing and hub assembly was discarded and never installed on the new bearing (That does not come with a shim) causing the new bearing to fail.

Jan 16, 2010 | 2004 Kia Sedona

1 Answer

2001 Impala Traction - ABS problems.


Is it the frt wheel sensor setting code again? If so I would check the connectors at wheel bearings I found most often terminal tension weak need to tighten or replace harness

Sep 10, 2009 | 2005 Chevrolet Impala

1 Answer

Wheel bearing


u have to take the hub off. and press the wheel bearing out. it takes alittle time to do bc u have to take your rotor and brake assembly off to get to the hub.

Jun 25, 2008 | 2001 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...