Question about Saturn Aura

1 Answer

Engine came on, gasmileage is decreasing and I believe a small critter has made a home in my air intake? Is it located under right front wheel well?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Saturn Master
  • 3,640 Answers

Need the year of vehicle and model!!

Posted on May 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is P0113 mean for a 01 merc cougar?


Intake air temperature sensor circuit. It is located between the air filter and engine. Small 2 wire plug. These rarely go bad. Usually it is a wire broke. And they usually break right at the plug.

Apr 15, 2016 | Cars & Trucks

1 Answer

How many airbag sensors in a 2008 gmc acadia


1) Front End Sensor - Right--Located under the front hood in the engine compartment (2) I/P Air Bag--Located at the top right under the instrument panel (3) Roof Rail Air Bag - Right--Located under the headliner, extending from the passenger front windshield pillar to the passenger rear windshield pillar (4) Side Impact Sensor (SIS) - RF--Located under the right front door trim near the lower rear of the door frame (5) Sensing and Diagnostic Module (SDM)--Located underneath the vehicle carpet under the center console (6) Seat Belt Pretensioner - RF--Located under the trim near the bottom of the center pillar (7) Side Impact Sensor (SIS) - RR--Located under the right rear door trim near the lower rear of the door frame (8) Roof Rail Module - Right--Located behind the garnish molding on the upper rear pillar (9) Roof Rail Module - Left--Located behind garnish molding on the upper rear pillar (10) Side Impact Sensor (SIS) - LR--Located under the left rear door trim near the lower rear of the door frame (11) Seat Belt Pretensioner - LF--Located under the trim near the bottom of the center pillar (12) Side Impact Sensor (SIS) - LF--Located under the left front door trim near the lower rear of the door frame (13) Roof Rail Air Bag - Left--Located under the headliner, extending from the driver front windshield pillar to the driver rear windshield pillar (14) Steering Wheel Air Bag--Located on the steering wheel (15) Vehicle Battery--Located at the front left of the engine compartment. (16) Front End Sensor - Left--Located under the front hood in the engine compartment

Aug 12, 2015 | GMC Cars & Trucks

1 Answer

Where is the iat sensor located on a 2011 dodge challenger 3.6 liter engine


The intake air temperature (IAT) sensor is located on the intake tube. Simply lift up on the engine cover to remove the cover. Near the front of the engine on the intake air tube will be a small 2 wire sensor, this is the IAT. Lift the release tab and rotate 1/4 turn to the left to remove it.

Nate

Mar 30, 2015 | Dodge Challenger Cars & Trucks

1 Answer

Location of 2.4l 2005 dodge stratus crankshaft sensor


On the Internet there are a lot of different descriptions of where the CRANKSHAFT position sensor is on the 2005 Dodge Stratus sedan 2.4L engine.

HERE IS WHERE I FOUND IT ON MY CAR:
it was on the front of the engine, behind/under the starter motor.

HOW CAN YOU TELL IF IT IS AT THIS LOCATION ON YOUR CAR:
- One website said that if the 8th number/letter in your car's VIN number is an X then it is located here (this was true for my car).
- To confirm: See if there is a wire (3 wires together actually) leading under the starter motor (see #2 below for a description of the starter motor's location).

THESE ARE THE STEPS I TOOK TO REPLACE IT:
1. Disconnect the positive terminal of the battery. (Turn the wheels all the way to the right, remove/pull back the black plastic cover of the front of the left wheel well, thus exposing the battery, and then unbolt the red positive terminal). You NEED to do this because you'll be working with the starter motor and you don't want to get shocked.
2. Unbolt the starter motor. You can see and access the starter motor from the top. It is situated on the front of the engine block, below the air intake (see the picture). It just has two 15mm bolts on the right side holding it on. You should be able to get a ratchet or wrench to them from the top, or you may even be able to get at them better from below.
3. Lift the starter motor up out of the way. I left all of the wires connected to it, and simply tied it with twine to the plastic air intake above to keep it out of the way.
4. You should be able to clearly see and access the sensor now (see the second picture). It has one bolt, and the plug. *Make sure to put a little oil on the rubber seal of the new sensor before inserting it.
5. Put everything back, in reverse order.

A COUPLE OF THINGS TO NOTE:
- I believe this applies to model years 2003-2006, and to the 2.4L Chrysler Sebring sedan of the same years.
- You probably don't need to jack your car up for this repair. I had my car up on ramps, but in the end I did everything from the top.


e5a262cb-58d3-4912-ac0e-371ae7cbade3.jpg

55cae5e6-03b6-484d-98af-4854d311adc5.jpg

Feb 03, 2012 | 2005 Dodge Stratus

2 Answers

Code po456?


The code po456 is leak in the evaporative emissions system.
First thing to check is for a poorly installed fuel fill cap

or try the following

1. Loosten the worm clamps that connect the air box hose to the intake.
2. Remove the bolt holding the air box to the radiator support.
3. Remove the small hose that comes off the front of the air box and goes from the air box to under the intake, I beleive this is the AIR tube.
4. Remove the AIT sensor from the intake hose.
5. Pull up on the air box.

Once removed set the air box a side. Locate the two lines that are wrapped in flex loom and tied to each other that go under the air box. They go from the solenoid that is mounted right next to the horn, behind the right headlight, to the rear of the vehicle. Locate a small 2" rubber hose that connects the front line to the rear line under the air box. Most likely this small hose that connects the two lines has a crack in it because it has been stressed from being stretched over a metal tube. If you replace this, it should fix your 'small leak'.

Reset the code by disconnecting the ground to the battery for a few minutes.

Hope this helps
Steve

Mar 02, 2011 | 2003 Chrysler Town & Country

4 Answers

Need the location of the MAF Mass Air Flow Sensor for a GMC Senoma 2.2 liter 1998 2 wheel drive truck. I can't find the ****** anywhere and I've exhausted every search engine combination I can think...


Hello ..There is a tube the your air filter connects to, and there is a ring(MAF) that couples into the air inlet tube right around where it passes the front of your engine. There will be a small electrical connection that will identify the location if you follow the tube coming from your air filter housing.

Nov 03, 2017 | GMC Sonoma Cars & Trucks

2 Answers

Where is the fuel filter located on a 1994 toyota pickup?


Not sure what engine you have, but on the 22R or 22RE (2.4 liter four cylinder) It's on the right side (passenger) lower engine just above the oil pan, and in front of the starter motor. You go through the inner wheel well just above the right front wheel. There is an access panel.

May 21, 2010 | 1994 Toyota Pickup

1 Answer

Cant find IAT on 99 jeep grand cherokee laredo...


Intake Air Temperature sensor.

It has to be installed ->BEFORE the throttle body, to sense the density of the air entering the intake manifold, based upon intake manifold temperature.

It provides an input voltage to the PCM, (Powertrain Control Module)
It's a Negative Thermal Coefficient sensor, (NTC. It uses two wires)

Meaning, as intake manifold temperature Increases, resistance in the sensor increases.
(Less voltage)
As the temperature Decreases, resistance in the sensor Decreases. (More voltage)

The PCM then uses this input to calculate the following;
1.Injector-Pulse Width
2.Adjustment of spark timing.

Just thought you might want to know.

Wish I knew what size your engine is.
A. The IAT in the 3.7 Liter engine, is located in the Left side, {Drivers} of Intake Manifold Plenum. (BEFORE the throttle body)

See that plastic 'snorkel' tube, that comes from the air cleaner housing, and goes to an oval shaped aluminum housing? That oval shaped, {On the end}, housing is the Intake Manifold Plenum.

The 4.7 Liter engine has the IAT in the same place.
The 4.0 Liter has the IAT installed INSIDE, the Front of the Intake Manifold Plenum. (Before the throttle body)

The color of the two wires are Brown with a Yellow stripe, (Thick 20 gauge wire), and Black with a Red stripe. (Thinner wire. 18 gauge)




Aug 07, 2009 | 1999 Jeep Cherokee

1 Answer

Where is the ac drain hose


Normal 0 false false false /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} -- open the driver's door
-- locate where the air conditioner blower box is attached to the passenger side of the firewall – see photo #1 – look to the immediate right at the top of the gas pedal arm
474e59d.jpg
-- condensation flows toward the front of the vehicle through the firewall at the leftmost edge of the air conditioner blower box – drain channel
-- open the hood and stand next to the front wheel on the driver's side
-- look down at the firewall over the battery and to the passenger side of the brake master cylinder – see photo #2
7fa75c5.jpg
-- locate the small diameter metal tubes running horizontally and attached to the engine compartment firewall
-- locate the hole in the engine compartment firewall panel behind the small diameter metal tubes
-- this hole leads to the drain opening in the air conditioner blower box mounted in the passenger compartment
-- follow the brake tubes as they run from under the vehicle and turn toward the front wheel on the driver's side
-- locate the hole in the engine compartment panel behind the brake tubes
-- insert a short length of stiff wire into the hole through the engine compartment panel to unblock the drain hole

Jul 11, 2009 | 2004 Mitsubishi Endeavor

1 Answer

2000 ford expediton a/c is blowing air but not through front vent


the problem is a vacumm leak , the control panel works with vacumm from engine supplied by small hoses and also have an vacumm tank under right front fender , check for disconnected hoses or break, the main vacumm hose is on engine intake manifold, ahh , also check control panel

Apr 25, 2009 | 2000 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...