Question about Nissan Frontier

1 Answer

Water pump torque settings terrano2 mistral 2.7td

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 510 Answers

IMPORTANT
M10 BOLT 27-37 Nm
M8 BOLT 17-23 Nm
good luck barry

Posted on May 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4610 ford diesel tractor water pump bolt torque settings


First you need to know the diameter of the bolts and the type of thread ie 3/8 N/C or 5/16 N/F then look at the type of bolt ie plain steel or high tensile SAE grade 3, 4, or 6, once you know this go to a general purpose bolt torque chart, and derive the torque spec info.
If the water pump is cast iron use the full torque specification.
If the water pump is alloy then reduce the torque spec 10%

Below is an example of a general purpose bolt / nut torque chart

26186159-4xbrgr0a3wt3vp4m2wlhd0as-1-0.jpg

May 05, 2016 | Ford Cars & Trucks

1 Answer

What are the torquing specs for a water pump on a 1992 Toyota pickup with a 22RE engine


the water pump bolts torque specs is T=1.85 kg-m (13 ft-lb). you must set your torque wrench nicely and carefully not to break the bolts then there you go.

Apr 03, 2016 | Toyota Cars & Trucks

1 Answer

Replace water pump torrent


drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs torque.you should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

What are the torqe specs for 2006 H3 fan/clutch and water pump


special tools you need EN 48543 FAN CLUTCH HOLDING TOOL. J41240 FAN CLUTCH REMOVER AND INSTALLER. TORQUE FOR FAN CLUTCH NUT 41 LB FT. FOUR BOLTS TO FAN BLADE TORQUE 20 LB FT.WATER PUMP BOLTS TORQUE TO 11 LB FT. DONT NEED SPECIAL TOOLS REMOVE WATER PUMP.

Nov 29, 2012 | 2006 Hummer H3

2 Answers

Water pump replacement torque settings


iv never torqued water pump ive always snugged them up pretty good i mean you don't have to stand on the end of the wrench if you use lock tight on the bolts once you tighten them up they wont come loose and you only need a drop of lock tight on each bolt hope this helps you bob

Apr 30, 2011 | 1999 Chevrolet Silverado 1500

2 Answers

How can I replace the water pump on a 2004 Grand Prix GTP superchargered?


WELL YOU NEED TO DRAIN COOLANT SYSTEM.PLACE A LARGE DRAIN PAN UNDER THE RADIATOR TO CATCH COOLANT WHILE DRAINING RADIATOR.ONCE ALL COOLANT DRAINED OUT.REMOVE DRIVE BELT.REMOVE WATER PUMP PULLEY.REMOVE POWER STEERING PUMP AND MOVE IT ASIDE.THEN REMOVE WATER PUMP.MAKE WATER PUMP MOUNTING SURFACE CLEAN THEN INSTALL NEW WATER PUMP AND GASKET IN PLACE.IF WATER PUMP GASKET IS PAPER TYPE PUT GASKET SEALANT ON BOTH SIDES OF THE GASKET.IF YOU HAVE RUBBER GASKET DONT USE NO GASKET SEALANT.INSTALL NEW WATER PUMP TORQUE LONG BOLTS TO 25 FT LBS AND TORQUE SHORT BOLTS TO 16 FT LBS.TORQUE WATER PUMP PULLEY TO 115 INCH POUNDS.TORQUE POWER STEERING PUMP BOLTS TO 25 FT LBS.THEN INSTALL DRIVE BELT.FILL THE COOLANT SYSTEM.START THE VECHICLE AND CHECK FOR LEAKS.

Mar 25, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

Installing new water pump on my Scout 2 (345 v-8). What setting do I torque the bolts to?


International does not give a torque spec. for the water pump, so use the bolt manufacturer spec.if i remember right the water pump bolts on a 345ci were 5/16in and 3/8in so 28-32 ft lbs on 5/16in 35-42 ft lbs on 3/8in......hope this helps

Dec 11, 2010 | Ford Bronco II Cars & Trucks

1 Answer

Change water pump on 1999 Century Buick


GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Water Pump - REMOVAL & INSTALLATION

3.1L and 3.4L (VIN E) Engines
  1. Disconnect the negative battery cable.

  2. Partially drain the cooling system into a suitable container.
  3. Remove the drive belt guard.
  4. Loosen the water pump pulley bolts before removing the drive belt. This should help keep the pulley from turning as the bolts are loosened.
  5. Remove the drive belt. Please see .
  6. Remove the water pump pulley bolts and remove the pulley.
  7. Remove the water pump bolts and separate the pump from the engine front cover.

To install:

1430070.jpg

Fig. Exploded view of the water pump and front cover arrangement-3.1L and 3.4L (VIN E) engines
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and torque to 18 ft. lbs. (25 Nm).
  4. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

3.4L (VIN X) Engine
  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container.
  3. Remove the coolant recovery reservoir.
  4. Remove the drive belt. Please see .
  5. Remove the pulley bolts and separate the pulley from the water pump.
  6. Remove the water pump bolts and remove the pump from the engine.

91d51fb.jpg

Fig. Exploded view of the water pump mounting-3.4L (VIN X) engine
To install:
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and finger-tighten the bolts.
  4. Install the drive belt, then torque the pulley bolts to 18 ft. lbs. (25 Nm).
  5. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

Hope this help (remember comment and rated this).

Apr 04, 2010 | 1998 Buick Century

1 Answer

How do I replace a water pump on a 1994 buick park ave


Removal
1. Support the vehicle on jack stands.
2. Disconnect the negative battery cable.
3. Drain the cooling system.
4. Remove water pump drive belt.
5. Disconnect the coolant hoses at the water pump.
6. Remove the water pump pulley bolts (long bolt removed through the access hole provided in
the body side rail), then remove the pulley.
7. Remove the torque axis mount. See TORQUE AXIS ENGINE MOUNT .
8. Remove the water pump attaching bolts and pump.
9. Clean all gasket mating surfaces.



Installation
1. Using a new gasket, install the water pump on the engine. Tighten the bolts to
specifications. See TORQUE SPECIFICATIONS .
2. Install the torque axis mount. See TORQUE AXIS ENGINE MOUNT .
3. Install the water pump pulley, then tighten the bolts to specifications. See TORQUE
SPECIFICATIONS .
4. Connect the coolant hoses onto the pump.
5. Install the water pump drive belt.
6. Fill the cooling system.
7. Add coolant supplement tablets.
8. Connect the battery cable, then start the engine.
9. Inspect for coolant leaks.

Jan 13, 2010 | 1994 Buick Park Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...