Question about Peugeot Liberte

1 Answer

How do you remove the front bumper on a peugeot 806

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 878 Answers

Jack car up choke wheels for safety ,behind the bumper is a set of four bolts and nuts loosen them and bang bumper out good luck

Posted on May 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the heater matrix on a peugeot 806


Clamp the hoses to the matrix or drain the coolant but you will still get a bit off leakage when you disconnect the hoses in the footwell
remove the glovebox door and the panel below and you can then see the blower housing

Jan 10, 2017 | Peugeot Cars & Trucks

1 Answer

How to remove a bumper on a peugeot 308


I have just finished replacing the broken grille on my wife's Peugeot 308 (09 reg) wiuth the help of a YouTube video in Russian .... http://www.youtube.com/watch?v=3-KxbwKnvJE ...not that I could understand what they were saying but at least you can follow what they are doing.

If attempting this, allow a good three hours which is what it took me as there are many bolts to undo and a knack of pushing and pulling fragile plastic lugs. Take your time.

Removal can be done without putting car on ramps as you will need to put the wheels on full lock to get at the wheel-arch liners.

Firstly, undo the various screws on the plastic tray underneath the engine which connect to the front bumper skirt. There are three main bolts with washers which are located half way back, one central and one each side.

Secondly, put the steering on full lock to give you access to the wheel-arch liner for each front wheel. Pull the wheel-arch liner back to reveal a 10mm bolt where the bumper meets the wing of the car. You will need a ratchet with a swivel knuckle and 10mm socket to get onto the bolt head. Undo the bolt and repeat on the other side.

Lift the bonnet and at the front edge you will see four black flat circles. Using a small flat blade screwdriver, lever up the centre and you can then lift up with your finger which releases the retaining plastic bolts.

Looking at the top of the panted front bumper where it attached to the front of the engine compartment, you will see several small slots along the width of the plastic which you can place a small flat bladed screwdriver into and push down gently whilst pulling the front panel forwards in a rocking motion to release the plastic lugs. The whole bumper assembly should then start disconnecting from the car. It is helpful to have a second person to gentle prise away the wheel-arch sections from the car body. The whole front bumper section should then fall away but be careful as the wiring for the front fog lights will still be attached. Take hold of the lamp holders and turn through 90 degrees to remove the bayonet fittings. Pull the bumper assembly clear of the car and place on a fabric cloth/mat to avoid scratching the paintwork.

Re-fitting is a reverse of the above.

Feb 23, 2012 | Cars & Trucks

1 Answer

How to replace radiator in 405 peugeot, how do you remove front bumper


remove the headlights ang grill then open the screws of bumper then open other two screws from the both sides of mudguard inside the mudd sheet. it is not necessary to remove bumper for removing of radiator just open two large screws of radiato and remove the pipes and lift it upward.

Aug 01, 2010 | 1990 Peugeot 405

1 Answer

How can I change the gearbox oil on a peugeot 806 manual vehicle the reg is 1996 I have had to put in a different model and year on the form as my car is not available as an option. My car is definatley a...


MOST MANUAL TRANSMISSION BEFORE CHANGING FLUID YOU DRIVE CAR AROUND.TO WARM THE OIL.SO IT WILL DRAIN OUT EASILY.NOW SAFELY RAISE VECHICLE AND SUPPORT IT ON JACK STANDS.LOCATE DRAIN PLUG ON DIFFERENTIAL PORTION OF THE CASE.GET SOME RAGS ON HAND.AND A DRAIN PAN.PLACE THE DRAIN PAN UNDER TRANSMISSION. REMOVE THE DRAIN PLUG.LET THE OIL DRAIN.WHEN FINISH.PUT IN NEW GEARBOX OIL.

Sep 06, 2009 | 1991 Peugeot 505

1 Answer

Warning Light


yes, on the expansion bottle or some rads on them its on the side of the rad there is a black square with a 3 or 4 oin plug on it.
remove this by i think half or quarter of a turn, and pull out, note some antifreeze will leak about half a litre, check for oil on it as this might of had a head gasket and a little oil gets into the water and sticks to the prongs, wipe it off, some time it like a limescale sort of build, clean it, if no joy u need a new 1

Apr 11, 2009 | 1987 Peugeot Liberte

1 Answer

Location of horn (s), Peugeot 806 2.0 HDi (2001)


in the corner of the bumper, i think n/s remove in **** shield or undo from bumper and pull back

Apr 09, 2009 | 2005 Peugeot 405

1 Answer

Peugeot 806 s reg front brakes binding


Flush the brake fluid at the calipers for the whole system. Keep adding new fluid into the master to be sure to flush it all and check to make sure you're using the same DOT spec (3 or 4). Water expands when it gets hot, possibly keeping positive brake pressure at non-braking. Brake fluid absorbs water and the only place to get water is at the seals in the calipers.
Bad flex hoses would be an all-the-time problem, not just at higher temperatures.

Jun 21, 2008 | Peugeot Liberte Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...