Question about 1998 Chevrolet Venture Cargo

1 Answer

How do I install a solenoid that goes on a 1998 Chevy Ventura Van

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,510 Answers

If you mean the starter solenoid, you have to remove the starter to change the solenoid.

Posted on May 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 Chevy Ventura van was running fine I turn the key over and nothing.but all the power works help


This could be a starter problem. You might try to rotate the harmonic balancer by hand if you can get at it. Then try to start it.

Oct 06, 2015 | Cars & Trucks

1 Answer

71' pontiac ventura, straight 6 250ci., how to wire the starter???


Hi Contact, You will need a low resistance (thick) cable from the battery to the starter motor. The cable fits onto the switching side of the solenoid (the heavy or large terminal of which there are two) The other cable goes into the starter motor. On the solenoid you will also see connections for two small cables. One is chassis ground and the other is from the ignition switch. The solenoid is basically a heavy duty relay. It has a throw in coil and a hold in coil. When these are activated by passing currant through them, they create a magnetic field, pulling a plunger into its center. The plunger is attached to a bus bar which carries the heavy amps which drive the starter motor. The starter has a field coil and an armature. When voltage is fed into the field coils it creates a circuit, passing through the field coils and via the brushes and commutator into the armature, through the winding and back to ground to complete the circuit. It too creates a magnetic field which spins the armature. Centrifugal force throws the Bendix forward, which engages into the ring gear and spins the engine. I don't know if you wanted to know that, but if you understand how something works its much easier to fix it. Best regards John

Sep 09, 2012 | 1998 Buick Century

1 Answer

Where are the freeze plugs on 1998 chevy venture Cylinder Heads


whats a chevy ventura looking like ?? iam a europeon mechanic and never seen one to be honest but if you look around the head you will find the core plugs at the back front and sides where the molten metal is poured into the sand mould and the aperatures let the air out and the sand mould after it has cooled

Oct 29, 2011 | 1998 Chevrolet Venture Cargo

1 Answer

Need the firing order for a 2000 Chevy Ventura van. I think I have two wires crossed. Thanks, Mark


Many firing orders here:
http://autorepair.about.com/od/fol/FOL.htm

I couldn't find a 2000 Venture, but here is a 2001:
2001 Chevrolet Venture
3.4 liter V-6 VIN "E"
zeevert_54.jpg

Mar 27, 2011 | 2000 Chevrolet Venture

1 Answer

Were is the reservoir for the rear window washer fluid in a 2000 Chevy Ventura van


on most chevrolet the rear reservoir is the front reservoir.the line runs through the inside of the car to the rear.

Feb 09, 2010 | Chevrolet Venture Cars & Trucks

1 Answer

I have a 1997 Chevy ventura van... Where is the


all you gotta do is follow the top radiator hose to motor,it;s where the hose meets the motor.

Dec 30, 2009 | 1997 Chevrolet Venture

1 Answer

My 2002 chevy ventura van data link connector not reading


why do they need to connect to engine ??? bit backward are we not ---where is the emmision analyser with the sensor up the exhaust ????and the full mechanical check ,brake roller tester ,shock absorber tester ,noise test?? over the pit with the wheels jerked about by metal plates to test ball joints and bearings.hammer to test for corrosion .NOT FORGETTING THE PAPERWORK ???

Mar 12, 2009 | 2000 Volkswagen Beetle

Not finding what you are looking for?
Cars & Trucks Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...