Question about 2002 Kia Sportage

Open Question

I have a problem the scanner show me p0326 in my kia sportage 2000, before i chanced the sparks?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2000 kia sportage ex, 4 cyl.

For that many codes I would refer you to a bulletin covering the 123 and 124 connectors. This bulletin has instructions on how to upgrade these 2 connectors which connect the engine to the ECM. The connectors are located under the intake manifold towards the firewall. You need to remove the battery, pull the connectors apart, give the male side a slight twist, then you add Stabulent 22 to the connectors and reconnect. The dealerships also add some clips to hold the connectors together better. This task is not an easy one due to the location of the connector. I have done it many times in the past and this helped many of my costomers. Anither thing to check is the continuity to ground at the MAF. This also can indicate bad connection throughout the engine harness. to upgrade this connection, clean the ground connections at the battery and under the battery tray. these simple uperations should have been made into normal maintenance for the 95 - 99 Sportages.

Posted on Mar 22, 2009

Ad
localwonder
  • 6784 Answers

SOURCE: the Abs light came on and will not go out after i

This is just a consequential event. the ABS sensor module was probably going out and decide the trigger the alarm at the same time you initiated the hard brake during travel. replacing or resetting this sensor module Will fix this issue. the light will go off as well.


Please rate and god bless.

Posted on Mar 17, 2009

  • 10 Answers

SOURCE: 2000 kia sportage. no start no spark no injector pulse.

check both of your fuse panels for a blown fuse. there's 4-5 that control the fuel pump, engine sensors, fuel injectors and such. one of those may be blown and not letting the rest of the system function. one panel is located under hood, and one is under the dash on drivers side. when you take the covers off they have the fuses numbered and tell what they control.

Posted on May 19, 2009

Molson02536
  • 3854 Answers

SOURCE: code for kia sportage tape and cd player

You can go to the dealer and have them help you get the code for the radio, if there going to charge you a crazy amount you can try www.radio-code.com. There cost is cheaper and can help you reprogram the code in your KIA. befor you go through all that, check for the code in the glove box, there might be a sticker in there or in your back pages to your manuel.
Good luck and hope this helps yougte your radio wokring again, keep me posted oh and try 0000 first. 

Posted on Jun 07, 2009

c17hydro
  • 2984 Answers

SOURCE: the easiest way to pull the heater core from a kia sportage-2000

There is no real easy way to do it....not like the older cars..

  1. Disconnect the negative battery cable.

    CAUTION After disconnecting the negative battery cable, wait for at least 10 minutes for the air bag module to deplete its stored energy.

    1. Remove the driver’s side air bag and steering wheel by performing the following procedure:
    2. Position the front wheels in the straight-ahead position.
  2. Remove the 4 steering wheel-to-air bag module bolts.
  3. Carefully, lift the air bag module and disconnect the electrical connector.

    CAUTION Place the air bag module in a safe location with the front facing upward.

  4. Remove the steering wheel-to-steering column nut.

    NOTE If may be necessary to mark the steering wheel to steering column alignment.

  5. Using a steering wheel puller, press the steering wheel from the steering column.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
    1. Remove the instrument panel by performing the following procedure:
    2. Remove both the rear and front consoles.
    3. Remove the knee bolster assembly.
    4. Remove the “T” bar section.
    5. Remove the relay bracket.
    6. Remove the turn signal assembly and the upper/lower steering column covers.
    7. Remove the hood release handle lockscrew, the hood release handle and the cable assembly nut.
    8. Remove the left side front pillar trim and the lower left side cover.
    9. Remove the 2 left side of the “T” bar-to-chassis bolts.
    10. At the left side of the instrument panel, remove the 3 instrument panel-to-chassis bolts.
    11. Remove the ashtray.
    12. Remove the center panel trim.
    13. Remove the ventilation control panel.
    14. At the center of the windshield next to the windshield, remove the cap and the mounting bolt.
    15. " Remove the right side front pillar trim and the lower right side cover.
    16. Remove the 2 right side of the “T” bar-to-chassis bolts.
    17. At the right side of the instrument panel, remove the 3 instrument panel-to-chassis bolts.
    18. Remove the steering column-to-instrument panel bolts and lower the steering column.
    19. Disconnect the instrument panel electrical connectors.
    20. Remove the instrument panel.
    1. Remove the blower/evaporator housing by performing the following procedure:
    2. Disconnect the air conditioning refrigerant lines from the evaporator core and discard the gaskets. Plug the openings to prevent contamination.
  8. Disconnect the fresh air control cable from the blower/evaporator housing inlet duct.
  9. Disconnect the 5 connectors from the bottom of the blower/evaporator housing.
  10. Move the carpeting from the bulkhead to gain access to the hole cover plate.
  11. Remove the 4 hole cover plate nuts and the plate.
  12. Remove the 2 upper blower/evaporator housing bolts.
  13. Remove the 2 lower blower/evaporator housing-to-bulkhead nuts.
  14. Remove the blower/evaporator housing.
  15. Disconnect the heater hoses from the heater core.
  16. Remove the temperature control cable from the heater housing.
  17. Remove the 2 lower heater housing nuts and the upper heater housing-to-bulkhead nut.
  18. Remove the heater housing.
    1. Disassemble the heater housing by performing the following procedure:
    2. Remove the seal from the heater core tube connections.
    • Remove the vent seal.
    • Remove the 2 wiring harness-to-heater servo screws.
    • Remove the 8 heater housing clips located on the servo side (left side).
    • Remove the left side of the heater housing.
    • Remove the 6 heater housing assembly clips.
    • Remove the 4 heater core tube mounting bracket screws and the bracket.
    • Remove the 8 remaining heater housing clips and disassemble the housings.
    • Remove the heater core from the housing.

  • f277857.gif
    Exploded view of the heater core and heater housing assembly—Kia Sportage


    THIS IS JUST TO REMOVE IT!

    Posted on Oct 18, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Video to show me how to take front struts of of a 2000 Kia sportage


    I can't find your year but the procedure is the same with maybe slight diffrences in the bolts and such. Here is a video that should do. Replacement of Front Struts on 2005 2010 Kia Sportage SENSEN Shocks and...

    Sep 20, 2016 | 2000 Kia Sportage

    1 Answer

    I need to know what code p0326 means for a 2001 kia sportage. i know it a knock sensor code what do i do with information.


    Knock sensor is an indication you are having a mis-fire with your spark plugs if one fires and another misses causes the engine to knock 3 possible issues.

    Spark plugs

    Older vehicle may need gas treatment

    Worst case valve or cylinder seal issue
    Try the first issues dont change knock sensor it maybe doing its job

    The last solution you shouldnt need to do unless you are getting black smoke from exhaust or engine is knocking realy bad

    Oct 15, 2013 | 2001 Kia Sportage

    1 Answer

    My 2000 kia show no.3 cylinder misfire so i replace the coil but nogood still misfireing


    Could be bad spark plug & or wire, try changing the plug & check the wire.

    Jan 15, 2011 | 2000 Kia Sportage

    1 Answer

    How do i change spark plugs on a 2000 kia sportage


    YOU REMOVE THE CYLINDER HEAD COVER.YOU REMOVE SPARK PLUGS FROM TOP OF THE ENGINE CYLINDER HEAD.FIRST YOU REMOVE THE IGNITION COILS AND HIGH TENSION LEADS THEN REMOVE SPARK PLUGS.YOU NEED SPARK PLUGS SOCKET THE LONGER SOCKET WILL BE GOOD YOU NEED LONGER EXTENSION, YOU NEED SPARK PLUGS GAP GAUGE AND A 3/8 RATCHET WRENCH. YOU NEED A TORQUE WRENCH ITS NOT MANDATORT BUT JUST DONT OVER TIGHTEN SPARK PLUGS OR YOU WILL DAMAGE THE ALUMINUM HEAD THREADS.

    Sep 05, 2010 | 2000 Kia Sportage

    2 Answers

    2001 kia sportage no start,cranks,no spark no fuel.snap on scanner will not communicate


    when scanners don't communicate usually is because the computer is bad.

    Jan 12, 2010 | 2000 Kia Sportage

    1 Answer

    Can't locate the spark plugs on my 2000 KIA Sportage


    SHOULD BE UNDER A COVER ON TOP OF MOTOR

    Dec 20, 2009 | 2000 Kia Sportage

    1 Answer

    How do you flush the radiator in a 2000 kia sportage?


    Its a safety thing. It makes gives the techs a chance to inspect your coolant, It removes any foreign contaminates that may or may not be in there, and as a tech you know exactly what the water to antifreeze(coolant) ratio is because they took all the old stuff out and replaced it.

    Jun 25, 2009 | 2000 Kia Sportage

    1 Answer

    What is it going to cost me?


    $12. UNLESS you have it done by a shop. Then $120.

    Jun 22, 2009 | 2000 Kia Sportage

    2 Answers

    2000 kia sportage. no start no spark no injector pulse.


    check both of your fuse panels for a blown fuse. there's 4-5 that control the fuel pump, engine sensors, fuel injectors and such. one of those may be blown and not letting the rest of the system function. one panel is located under hood, and one is under the dash on drivers side. when you take the covers off they have the fuses numbered and tell what they control.

    May 16, 2009 | 2000 Kia Sportage

    3 Answers

    We have a 2000 Kia sportage 2.0 litre that was given to us because it did not have any power. It would not go over 15 mph. #1 plug wire and #3 plug wire was off. We hooked it back up and started the...


    Chances are the spark plugs are loose and need to be tightend.
    The compression is being pushed past the plugs and blowing the wires off.
    This is best case senario.
    Let me know what you find and I can assist further.
    Please rate this solution.
    Lone99star

    May 06, 2009 | 2000 Kia Sportage

    Not finding what you are looking for?
    2002 Kia Sportage Logo

    Related Topics:

    391 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kia Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8266 Answers

    Are you a Kia Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...