Question about 2002 Volkswagen Golf

1 Answer

There is oil word in my tablu .. and i change the oil and the fillter .. i think its elc ..thing ? or what

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 188 Answers

Its a service indicater it needs to be canceld with a vag.or u can do it manualy by holding in the right hand side pin on dash with ignitin of and still holding pin switch on ign and turn left side knob to right.hope it helps

Posted on May 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the timing marks for a 1996 toyota camry, 2.2


2S-ELC, 3S-FE and 5S-FE Engines

When install,
align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).

On 2S-ELC engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
Align the camshaft knock pin with the matchmarks on the oil seal retainer.

On 2S-ELC/USA engines, align the knock pin with the pin hole on the timing pulley E mark side. On 2S-ELC/Canadian engines, align the knock pin with the pin hole on the timing pulley.

On 3S-FE and 5S-FE engines, align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt.



Apr 29, 2011 | 1996 Toyota Camry

1 Answer

Have a 03 matrix with a oilpump promblem I think,bought the car last week ran good next day was drive on highway notice oil lap on and noise from motor ,slowed down light went off.Next day change oil and...


Generally three things can turn the light on. First is the sending unit itself if it's going bad. Next is an obstruction of the pump pickup screen (usually hard carbon deposits). Third is worn engine bearings (usually rod bearings). Best way to find the problem is to have someone put a mechanical pressure gauge on the engine and read the actual pressure. If it's low you need to go into the engine to determine why. if it's normal, replace the sending unit. Senders aren't terribly expensive and you could just buy one and replace the one you have, providing the engine isn't tapping or knocking.

Mar 14, 2011 | 2003 Toyota Matrix

1 Answer

Iv got a disco 1.And when im towing and need more power, it wont rev above 4000 revs. checeked all the hoses, cleaned the intercooler, replaced fuel/oil fillter, give it oil change.Its got a KnN air...


Hi,
Are you getting a lot of black smoke?
If so your egr is more than likely goosed.
Easy fix in a 300.
Mine suffered from this a few years ago and I blanked off the egr. You can make a blank yourself or buy one with instructions for a few quid of eBay.
Well worth it and you will certainly notice the difference.
hope this helps.
Iain

Oct 11, 2009 | 1995 Land Rover Discovery

1 Answer

Temp gage not moving


dus your car an elc fan? if so you need to check the fan relay check that the corecekt voltage is ther and the sening unit of the turmostat is working if all is well check the fan if fan is working replace fan relay som far relay are in conjunkson with the a/c relay. hope this helps

May 19, 2009 | Audi 80 Cars & Trucks

1 Answer

Oil coming out of oil fillter


hello,good day,try to clean your engine breather,if ok,lift up your deep stick,while your engine is running,then observe if there is a huge volume of pressure,if yes,perform engine compression test,to evaluate your engine condition,ty

Mar 13, 2009 | 1985 Mercedes-Benz 300

1 Answer

99 chevy suburban sevice engine soon light is on.


While the CEL is on you need to take it to an autoparts store and have the code read to know what is exactly going on. Just cuzz it seems to be running fine does not mean there isn't something wrong.




Please don't forget to rate.

Mar 08, 2009 | 1999 GMC Suburban

1 Answer

Oil change for 1998 mercedes S 320


jack up car there is a big nut at bottom or side of eng remove drain oil then replace look up the side of eng you will see round fillter marked oil filter remove then replace then fill oil on top of eng check level as you go

Jan 17, 2009 | 1998 Mercedes-Benz S-Class

1 Answer

My 1996 Toyota Camry makes a strange sound whenever I start


1.check your water pump

2.check if the engine oil light is offing in time or not,it is like the engiine oil is not being lifted in time by the oil pump,

3. what should do if is number 1 u have change the water pump and if it is number 2 then change the oil fillter drain the engine oil and replace with new one but this time around add oil treatment oil to the engine oil u change if it is sea 40

Dec 15, 2008 | 1996 Toyota Camry

Not finding what you are looking for?
2002 Volkswagen Golf Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...