Question about 2000 Jeep Grand Cherokee

1 Answer

I have a grand cherokee 2000, at first it used to have the check gauges signal on, and never turn on the engine for a while, just after some hours the signal go and it is start, but now when the engine decides to start, and it start runnig for several minutes it is get shut dowm while i am in the road. cod is P0320, what should i do? Thank You

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 273 Answers

P0320 (M) No RPM Signal to PCM (Crankshaft
A CKP signal has not been detected at the PCM
Position Sensor Signal to JTEC)
Try changing your crank sensor. Hope this helps, James Booth

Posted on May 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 jeep grand cherokee will not start and battery guage is dead


if the other light is ok and the fuel gauge is only dead, may be you have no more fuel, try to refill fuel, if the battery is also dead replace new battery.

Oct 28, 2012 | 2000 Jeep Grand Cherokee

1 Answer

2000 Jeep Grand Cherokee Laredo electrical issues


i suspect maybe the battery is low. get it load tested. jeeps can be funny like that

Jun 15, 2017 | 2000 Jeep Grand Cherokee Laredo

1 Answer

2000 Jeep Grand Cherokee V8 Car will suddenly stall, fuel gauge down and won't start. Wait for about 1 hour or more, sometime less, fuel gauge comes on and engine starts. replace P0117, plugs, fuel...


Hello and welcome to FixYa!
I'm suspecting that the PCM (power train control module) is faulty. If the PCM is faulty the electrical fails at any given time. The PCM is like a car's brain, I strongly suggest that you have it replaced as a first course of action.
Hope this helps and thank you for using FixYa! Have a good one!

May 03, 2011 | 2000 Jeep Grand Cherokee

1 Answer

What is the correct oil pressure for 2000 grand jeep cherokee larado its about 75 now. i want to buy this car but worried about the oil pressure.


Normal oil pressure should be between 40 and 60 psi. A cold engine will normally have higher pressure. If you're seeing 75 psi on a warm engine I would recommend having the pressure checked with a manual gauge to verify the gauge in the Jeep is working correctly. If the gauge is correct oil viscosity may be too high (oil too thick) or there may be a problem with the oil pump pressure relief valve. If the gauge is not correct the sending unit may be at fault.

Apr 09, 2011 | 2000 Jeep Grand Cherokee

2 Answers

2000 jeep cherokee sport. the "check gauges" light


check all hose clamps and tighten them up.Do not do this until motor is cooled down and add coolant to level mark on holding tank.

Apr 04, 2011 | 2000 Jeep Grand Cherokee

1 Answer

What does it mean when the check gage light come on and the oil pressure hand goes to the zero mark? I have a 2000 jeep grande cherokee limited with 124,000 miles.


Either the oil level is very low or the engine bearings have failed (assuming the gauge is accurate) if the engine isn't making noise and the level is full have a mechanical gauge installed to check actual pressure. if good, the sending unit or gauge is faulty.
If in doubt, do not drive or run the engine 'tll the problem has been diagnosed.

Feb 04, 2011 | 2000 Jeep Grand Cherokee

1 Answer

2000 grand cherokee V-8 stalls out


Start the engine cold and as it warms up, pull the vacuum hose off the EGR valve and see if it keeps running. If it does, replace the EGR valve. The reason the lights are all coming on and the gauges go to zero is because the engine dies and when it starts they return to normal. The EGR valve can stay stuck closed from carbon deposits which is fine for the warm up mode but it needs to open when the engine is warm or it will choke it out. This is not unusual and you will need to replace it. Look on the internet for your make and model an image of your EGR valve it will be easier than explaining it to you. They are in most cases on or connected to the intake manifold or intake plenum.*** Please rate me on this answer.***

Jun 06, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Won't start. Engine will turn over. dash gauges won't activate. 2000 raand Cherokee 4.7.


Try to borrow a diagnostic tool and plug it into your computer under the dash by the steerig wheel. You might have to crank the engine while checking it.

Jul 30, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Oil pressure problem


have u had the oil pressure double checked with a mechanical test gauge? most times the sender on the engine is giving a false signal.

Jun 07, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

386 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...