Question about Hyundai Accent

2 Answers

I have changed the timimg belt we have everything is lined up the car will run but runs rouf with with tapping in the motor .I would if that could be a bent value.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 6,982 Answers

Yup...sounds like you've bent a valve.....To check, put a vacuum gauge on the engine. if the needle bounces a valve is bent. If it's an exhaust valve it may not bounce as much as an intake will. Another way to check is to look at the valve spring heights. Usually if a valve is bent, that spring will be lower than the others. If you can't see the springs, check clearance between the cam and the followers.

Posted on May 17, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Hyundai Master
  • 1,810 Answers

Posably could be a miss alignment or bent valve could be a lot of stuff check the compression this should tell you

Posted on May 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installed timimg belt on a 05 Chrysler Pacifica 3.5L V6. Marks are aligned correctly with engine on TDC. But car starts like timing is off. Has no power. No codes present. Running out of ideas. Can so


I have had this problem on one car where the inside of the gear has detached from shaft , another where the distributor had mal alighned its weights

Jan 06, 2015 | 2005 Chrysler Pacifica

1 Answer

How can the timimg belt affects the reving of the 4d56


If the belt jumps time due to wear on the teeth then it plays heck with everything, and the engine will run like do do.

Oct 30, 2012 | Mitsubishi Cars & Trucks

1 Answer

How to time the timimg belt for a 1995 labaron v6 conv put a new water pump in need to set the timimg belt how do i line it up


get the #1 piston top dead center, then line up the camshaft gear and the crank gear to line up with the timing marks on the engine after you find those marks slip the belt on making sure all the timing marks havent changed then check to see if the tensioner for the belt is set with the proper tension then check to see if the belt isnt slipping remember it will be spinnig at high RPMS

May 03, 2010 | 1995 Chrysler LeBaron

1 Answer

Symtoms of a bad timimg chain/belt...but ran real


Problem is not solved but I did change the fuel filter, coil pack,ICM and have proper fuel pressure to the motor. Car starts but dies right away. I cant seem to find out if the fob on the key ring has something to do with stopping the motor. This fob says Radio Key by Secure Key with a number 35077 stamped on this thing.. Still trying to find out what this is and does it effect the cars ability to run

Mar 15, 2010 | 2004 Oldsmobile Alero

1 Answer

Kia sephia timimg belt replacement


remove drive belts and water pump pulley remove plastic cover and crank pulley line marks on cam with marks on valve cover should be at 12 o clock then there is a notch in crank gear that lines up with *** on the block at about 1 o clock the tensioner is spring loaded 14mm nut loosen this nut use a pry bar to push tensioner back snug nut so pulley wont come back remove belt when installing new belt use paper clibs wit the rods that flip over to hold the belt on the pulleys be sure timing marks on cam are lined up before attaching clips as they will move when belt is removed after belt is installed and tensioner is tight turn engine by hand until cam marks are lined up be sure all marks are lined up if they are reassemble everything and happy motoring

Aug 06, 2009 | 1998 Kia Sephia

1 Answer

96 quest.. possible timimg, stopped running at 30mph


check possible broken timing belt by....
removing the distributer cap , and having someone try to start the car .
While it's trying to start , the rotor should be moving... if it's not
timing belt is broken
It's a big job for someone without great skill and a great selection of car tools

Apr 21, 2009 | 1996 Nissan Quest

1 Answer

Cold engine start on 2002 toyota tundra


JUST MAKE SURE YOU HAVE THE RIGHT AMOUNT OF OIL IN THE MOTOR 7 ITS IN TIME.IF IT DOESNT GET ANY LOUDER,DONT LET IT GET YOU NERVOUS. PS ONLY IF IT DOES START GETTING LOUDER YOU MIGHT WANT TO TAKE IT BACK IN TO WHOMEVER DID THE BELT

Dec 28, 2008 | 2000 Dodge Durango

1 Answer

95 buick pv run a little rouf & loses coolent.


If I am following you, it sounds like you may have a bad head gasket. Do you still need help with this?

Jun 26, 2008 | 1995 Buick Park Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...