Question about 1999 Ford Crown Victoria

1 Answer

Check engine light on

I use a decoder to remove the light, But after a while the check engine light start blinking then it stays on, i notice when i go between 39 to 40 mpg i get a vibration like something from the tranny.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

When the check engine light flashes this is a class a misfire. If this is a 1999 you have a spark plug or a spark plug wire bad. Get a tune up done and replace plug wires.

Posted on Sep 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My check oil lights keep on blinking.. Oil is full...I noticed it started blinking after I change my radiator.


have you left a wiring plug off or pulled one off and not noticed front of engine on the lower block area

Aug 05, 2014 | Cars & Trucks

1 Answer

Where is diagnostic connector locationon 1994 toyota base pickup


The check engine light is used to blink out the trouble codes. The diagnostic connector is usually under the hood on driver's side, back near the firewall. Sometimes under the driver's dash. Use a jumper wire and connect terminals TE1 and T1. Then turn key to on, not start, and the check engine light will blink out the trouble codes. If no codes are present, the check engine light will stay on constantly. Remove jumper wire when diagnostics completed. To clear codes after repairs, disconnect the negative battery terminal for one minute, and then reconnect.
This site has Toyota code explanations:

Dec 30, 2013 | Cars & Trucks

2 Answers

My engine light just started blinking


Thanks for choosing FixYa and welcome.

Jun 09, 2011 | 2004 Saab 9-3

1 Answer

2003 Prius sometimes will not start, engine light comes on. Removing key from ignition, reinserting key, & turning wheel till it locks will then allow the car to start. Engine light stays on for a


I had a wire connector on the front of the engine that had so much tension, the wires broke. I didn't notice until a wet day when the car wouldn't start (and the Check Engine light was on). (The error code was related to an Emissions error.) The connector is located on the engine, front, just left of center. Hope this helps!

May 25, 2009 | 2002 Toyota Prius

1 Answer

Over drive light on shifter blinks and check engine light is lit.


You need to have it scanned for codes. The flashing overdrive light means it has trouble codes that pertain to the transmission.

May 23, 2009 | 1998 Ford Expedition

2 Answers

Car want start but turns over


I had the same thing happen to my 2001 Grand Am. Do this.......just key the key, but don't turn it over. Your Security Light should be blinking. Let it blink for about 10 to 15 minutes, it should stay on after that. When it stays on, turn the key and it should start. I still have to do this once every 3 the 4 months, some sort of security problem that cost to much money to fix.

May 13, 2009 | 2001 Pontiac Grand Am SE

2 Answers

2003 AUDI Quattro 3.0 check engine light(MIL) stays on


you will have to have it hooked up to a computer to decode the light and find out what is going on. I would take it to a reliable mechanic

May 06, 2009 | 2005 Audi A4

2 Answers

2000 Lincoln LS--Check engine light blinking/sputtering take off


you need to find out what codes have been set
one of your coil packs is going bad.
the code should tell you which one
let us know how you do
later
paul

Nov 19, 2008 | 2000 Lincoln LS

1 Answer

Car cut off when running several times but will not start back up.


O K I'm going to try and explain how to do this. What you need is the codes out of the computer. Here is how you access the codes. Turn the ignition switch on then off then on then off then on again. now leave it on and count how many times the check engine light blinks. Will say the code is 35, what you will see is the light will blink three times then hesitate then blink 5 times and this is 35. you may have more then one code in the computer so watch and count them all and write them all down. Then go to Auto Zone and give them the codes and they will tell you what's wrong. do not start the motor when you are getting the codes.

Jun 23, 2008 | 2005 Buick LeSabre

Not finding what you are looking for?
1999 Ford Crown Victoria Logo

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...