Question about 2001 Mitsubishi Montero

2 Answers

Replace front wheel bearings 1998 lancer - 2001 Mitsubishi Montero

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do i remove the front wheel bearing hub assembly?

Posted on Nov 05, 2008

  • sn75ake Nov 05, 2008

    THIS IS FOR A 2001 MONTERO 4X4 NOT A 1998 LANCER

×

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Ask MIbearings LLC for wheel bearings - http://mibearings.com

Posted on Jan 10, 2009

2 Suggested Answers

keemo68
  • 1263 Answers

SOURCE: replacing front wheel bearing

those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

Posted on Aug 28, 2008

  • 100 Answers

SOURCE: noisey front end

sounds like a tire when it starts gettin noise start weavin back@forth r ight to left and see if the noise comes and goes

Posted on Oct 21, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

ES Lancer - vibration, dull grinding noise when turning right, even at low speeds. Intensifies as I approach 30+mph. Replaced CV Axle, Tie Rod End, Bearing, and Hub. No dice.


Turning right and having a loader noise, means the left/drivers side is bad. Turn right, more pressure on the left side. and vice versa.

Aug 09, 2015 | 2003 Mitsubishi Lancer

1 Answer

How do I replace a front wheel bearing?


front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

Aug 03, 2014 | 2002 Mitsubishi Lancer

1 Answer

Lancer vibrates at 90 to 100 ks at front at front left


bent rim, tires out of balance, worn cv axle, bad wheel bearing, warped brake rotor, bad tire. Change that wheel to the rear, and see if the vibration moves with the wheel. Depending on the vibration, could be a motor/transmisson mount.

Dec 17, 2013 | 2002 Mitsubishi Lancer

1 Answer

Replace front wheel bearing on 1998 saturn


The easiest way is to buy the knuckle and front hub together. It is more expensive but unless you have access to a press to press the knuckle from the hub and then press a new bearing in it will be impossible to replace.

Also like any wheel bearing job, change in pairs not just one. So change both front wheels because if one is going then the other is not far behind.

Jun 12, 2010 | 1998 Saturn SL

1 Answer

Replacing front wheel bearings


fronts are bearing ahd hub assy remove the black center cover remove the hub nut and the hub should slide off. the caliper and rotor also have to be removed

Apr 20, 2009 | 1998 Lincoln Town Car

1 Answer

Need torque spec for axle nut 2003 lancer


THE BIG NUT DONT TORK IT SHOULD HAVE HAD A CARTER PIN IN IT THAT KEEPS IT FROM BACKING OFF BUT U JUST SNUG IT UP TIGHT THIN TURN 1/2 TURN PUT CARTER PIN IN THE HOLE IF U TIGHTING THIS NUT REAL TIGHT THE BEARING WILL GET HOT AND LOCK UP ON U GOOD LUCK PLEASE RATE THIS

Apr 05, 2009 | 2003 Mitsubishi Lancer

3 Answers

Replacing front wheel bearing


those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

Aug 28, 2008 | 2003 Mitsubishi Lancer

2 Answers

HELP!


yes the bearings are pressed in. have to find a press

Jul 29, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2001 Mitsubishi Montero Logo

1,727 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...