Question about 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Ignition switch How do I change the ignition switch on my 2000 F250 Super Duty

Posted by on

1 Answer

PUT KEY IN IGN CYL.TURN TO RUN POSITION.THERE IS A SMALL HOLE UNDER IGN CYL WITH A SMALL BALL IN THE HOLE PUSH IT UP AND PULL ON KEY TO REMOVE.

Posted on Oct 22, 2008

  • 2065236087 Aug 26, 2011

    what if the key wont turn?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 f250 V10 gas super duty. Cranks but does not start in cold weather. Truck is from warm weather area now in freezing weather for first time. No pressure from fuel pump. Pump changed, same problem.


Ok you have no pressure from fuel pump to the injectors and you replaced the pump. Sounds as if you need to check or replace the relays which send the signal from your ignition switch to your fuel pump to engage/shutoff. Warm weather area sorry doesn't really apply unless you're in an older carburated vehicle

Dec 10, 2010 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

I have a Ford F250, 2002 super duty v-10. My battery died and I tried jumping it but the alarm sounded. (I never received the push button entry thing). I bought this truck used and need to know how to...


Depending on the alarm system, there may be a valet button under the dash on the driver's side near the stearing column. You will need to put your key in the ignition, turn the key to the on position and then press the button in.

Oct 21, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

F250 engine code 358 v8 gas


That is the code for the primary circuit of the ignition coil. It is for the failure of the primary circuit. This should mean a problem with the wiring to the coil pak.

Mar 31, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Fan stays running with key off. Have changed


which fan? if you are talking about the engine fan, it will run on until the temperature drops, but if you are talking about the heater fan, thats not right

Jan 31, 2010 | 2001 Ford F250 Super Duty Super Cab

2 Answers

I have a 2000 F250 7.3 diesel, I keep blowing the #30,30 amp fuse, fuel heater fuse. Why?


most likley the fuel heater is bad and shorting out happend to me replace the heater

Jan 07, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Truck wont start at the starter switch sometimes. I turn the key and nothing happens. I can go to the sylinoid (bad spelling) and start it with a screw driver


Probably a bad ignition key contact (worn out).
You can hook a pushbutton across the + to key wire terminal... the start it like an old fashened car (turn on the key and push the starter button....when the ignition contact fails to "make".

Oct 12, 2009 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

2000 ford f250 w/ triton v-10 Battery drains within 1-2 hours of turning off ignition. have to disconnet the battery every time I stop the truck to avoid a dead b attery. Radio, power windows, etc all...


check glove box light if equiped, interior lights that no off when you close the doors, also some radio, cb, dvd, etc. if all good check alternator for possible drain

May 03, 2009 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

Not quite sure how to change my ignition cylinder dont see a push button like other ford models


Here you go. If this solves your issue, please rate as Fixya. Good luck. Ignition Switch Lock Cylinder —Functional Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key and turn to the RUN position.
    1. Using a 1/8-inch drift, press the ignition switch lock cylinder release pin through the access hole while pulling out the ignition switch lock cylinder.
2e15945.gif
  1. To install, reverse the removal procedure.
    • Verify ignition switch lock cylinder operation.
b141ce9.gif

Mar 01, 2009 | 2002 Ford F250 Super Duty SuperCab

1 Answer

How do i change a turn signal switch on a 2000 f-250 ?


Look in the bottom cover underneath the lock cylinder and u will see a hole there.Turn ignition switch to on postion then stick a small screw driver or pick into the hole an push the release pin then pull the lock cylinder out.

Feb 18, 2009 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

My ignition switch is broken


this is a common ford ignition cylinder problem.you can buy a new key cylinder at a checker or autozone cheap.remove column cover and push small metal button and cylinder comes out

Jan 17, 2009 | 2001 Ford F250 Super Duty Super Cab

Not finding what you are looking for?
2000 Ford F250 Super Duty Crew Cabs Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...