Question about Chevrolet Camaro

1 Answer

I recently swapped my tranny. its a super t 10 4 speed, it worked fine when i pulled it from the 1980 camaro, iput it in my other 1980 and now my transmission wont go in any of the gears, it will go into rev and ive adjusted the clutch it is engaging all the way. does anyone know?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 398 Answers

Did you adjust the shift rods from the shifter to the trans shift arms. Take your shift rods loose and put shifter in neutral, and transmission arms in neutral, then adjust the rods so they slide in. Then your shifter matches your transmission and you should be able to shift just fine.

Posted on Aug 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can I interchange a 1980-1985,305 chevy engine with a 1991 305 chevy?


as it is the basic 305 block the differences may be fuel injection over carburettor which may require sensor attachments but basically the engine should just slot in place.

Feb 05, 2015 | 1991 Chevrolet Camaro

1 Answer

I bought this car knowing I would need to get a new radiator. Everything else was good. I got a U-Pull used radiator and i blew about a month later. So I got brand new lifetime warranty from...


Man it sounds like you a pretty experianced wrench!
I have solved some of thes electrical gremlins with putting good ground cables fron the engine to the chassis. The electronics get happier with a solid ground

Good luck

Oct 13, 2010 | 1989 Chevrolet Camaro

1 Answer

Transmission stuck in 1st gear on a 87 camaro iroc-z


If the moudulator (vacuum controlled) is bad it will stay in low,Not sure what tranny,but if it has a vacuum line going to it ,start there,if you pull the vac. line off and fluid drips out ,it's bad.
If a 700r 4 speed ,Pull the cover for the governor (should have a wire clip over it,like a master cyl clip ,kinda) It's just pressed into the housing. A small amount of fluid will leak out. Just grab the governor by the end and pull it out ,The gear on the end is plactic,if it's "applecored" the governor can't work. I've replaced mine a few times.
Oh yea ,check the kickdown cable first,make sure ,if you pull on it ,you can feel the spring pressure aginst it as you get to the end.

May 14, 2010 | 1985 Chevrolet Camaro

1 Answer

Tranny wont shift out of first


the tranny seals are leaking from sitting so long, pull the trans and replace the internal seals.

Aug 12, 2009 | 1990 Chevrolet Camaro

1 Answer

99' camaro auto tranny wont engage


take it back to transmission shop that did the work, or have towed back on their ticket

shack

Apr 16, 2009 | 1999 Chevrolet Camaro

3 Answers

2000 dodge caravan engine and transmission swap


Although the transmission may be siilar, the engine and supporting wiring harness, and control modules are not. This can be done, anything can, but it is probably more trouble than it's worth for a mini van. If this was a classic car then sure.

Dec 06, 2008 | 2000 Dodge Caravan

1 Answer

I have a 1988 chevy camaro z28 and first gear works fine second gear will aonly go to 2500 rpms and then will slip out, unless i punch it, then it will catch the top of third gear. but i cant go lower than...


sounds like you need a tranny, or perhaps check the modulator, pull the the vacuum line off of it, if tranny fluid comes out then, the diaphragm is split.

Aug 05, 2008 | Chevrolet Camaro Cars & Trucks

1 Answer

1993 Camaro v6 3.4 lt


The cheapest and easiest ways to increase HP is intake and exhaust. Swapping a whole motor is a lot of work that comes with many headaches. A good aftermarket cold air intake will add 5-10 HP and you can bolt it in quick and easy. And putting on a good free flowing exhuast can add up to 25HP. Basically the intake allows more air into the motor creating more power, and if you get more air in you are gonna want that exhaust to get the air flowiing back out. So for a few hundred bucks you can get your car performing and sounding great.

Hope this helps.
And yes a 350 would fit, however you will need to swap your tranny to accept the 350 motor. Alot of work if you ask me.

Jun 26, 2008 | 1993 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...