Question about 1991 Toyota Pickup

1 Answer

Need to put a new bed on 1991 pick up how hard is this?

I have never done this before how do i go about it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

You need to remove the fuel filler tube, disconnet the harnesses that hook to the taillamps, the license plate lamps and any other wiring. Spray penetrating oil around the bed bolts before you remove them. Undo the bolts & have people help you lift the bed off. Not a "hard" job, but a rather heavy type of job. I commonly pull the beds whenever I am changing the fuel tank sending unit.

Posted on Sep 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I take the bed off an izuzu pick up 1991?


remove the bed bolts. and wires./hoses. etc.
just crawl;under , its obvious to a point.

didnt look first?

Apr 14, 2015 | Isuzu Cars & Trucks

1 Answer

How to remove gas tank from 1991 chevy 1500 4x4 how to remove the straps


It is easier to take the bed loose and pick up the bed. there is 8 bolts and the gas filler neck too take loose.first you open up the gas door, and around the gas cap there will be 3 7mm screws then under the truck the 15mm bolts are on top half of the frame.these bolts are spaced from front to rear on bo th sides of the bed.then look at the rear of the truck, behind the bumper. you will find a plug that goes to the taillamps. unplug that connector .4 or 5 guys move can pick that bed up and just move it backwards,over the tires.if you dont have the manpower then take a big floor jack and position a 4x4 about 1/ 1/2 ft long. stand the 4x4on the jack saddle, and jack up the bed.pay close attention to the gas filler neck and other things, while going up. just go slow, up and down. you will need someone to watch the filler neck when you go back down

Oct 23, 2011 | Cars & Trucks

2 Answers

On an 81 through 87 chevy truck. my question is the only difference between the short wide truck and the long bed the lenght of the bed? i have a long bed and what to take the bed off and put a short bed...


No I don't believe it will as the frame/ wheel base is different. to check measure from the front of the bed to the bolts in the bed. This will let you know.

Feb 19, 2011 | 1985 Chevrolet Chevy

1 Answer

I need to take off the belt how do i take it off a 1991 buick skylark?


You will have to loosen tentioner to get belt off of all pulleys. Then you need to jack up engine or pick up engine with a lift of some kind, just enough to hold engine in place while you remove upper engine mount, this has to be done so as to slip belt past mount and off engine. Then put new belt in position and bolt mount back in place. Release jack or lift. I usually put belt back on everything but alternator, pull on tensioner and roll back over alternator. This is on a 3100 engine, or 3.1 liter.

good luck

Jan 03, 2011 | 1995 Buick Skylark

1 Answer

I did knoc the bottom of the tank but sometimes it starts and now nothing what to do,?


Knocking on the tank is usually a temporary fix just to buy some time. If it isn't working anymore you'll have to either drop the tank and change the pump inside, or take the bed off to do it. With two people I've found the bed is easier and quicker. Six bolts hold it on and the 3 screws in the gas cap. Unplug the tail light wires. Can be done in about an hour. Dropping the tank is the other option and I hate dealing with something that has to be held up (the tank) as opposed to just setting it back on and putting the bolts back in (the bed).

Dec 02, 2010 | 1991 Chevrolet S-10

3 Answers

My brakes arent working correctly after getting new pads & rotors


Go back to where you had the brake job done and tell them they did not bleed the brakes correctly and it is causing you problems. Make them road test the car before any work is done. Once they bleed the system it more than likely will work normally

Jan 15, 2010 | 1994 Mitsubishi Montero

1 Answer

Are the valves adjustable on the 1990 3.0L? I


1) The valves are adjustable, but they are of the shim-type adjustment. You will need to obtain the proper shims from a dealership parts department.

2) Any Toyota dealer can, by you giving them your VIN, tell you whatever was done to the vehicle under warranty

3) There are no special service campaigns for bed replacements, nor has there ever been one. Any bed that 'was' replaced was under factory "goodwill", to maintain customer satisfaction.

Oct 06, 2009 | 1991 Toyota Pickup

2 Answers

Will not start, does turnover, but seems to be getting no gas. will turn over if i spray auto start in the carborator.


check fuel filter to see if its clogged. (cheapest easiest)
if that doesnt work rebuild carburetor (expensive but fairly simple)
if that doesnt work pull tank if it is low on gas or pull bed if gas tank is full a replace fuel pump (time consuming, hard to do, but fairly inexpensive) I had this problem on a silverado I had and it was the fuel pump.

Sep 30, 2009 | 1991 Chevrolet C1500

2 Answers

Best way to empty fuel tank


Syphen...

Or a Rabit Pump..
Its a hand crank pump..

Hope this helps !!

Jul 14, 2009 | 1987 Ford F 150

1 Answer

Tail light


there are 2 screws take them out get a putty knife andslightly put in between the tail light and bed jiggle it then pull firmly on light towards you chould come right out/Please rate my response thank you very much

Jan 27, 2009 | 1991 Nissan Pickup

Not finding what you are looking for?
1991 Toyota Pickup Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...