Question about 2001 Toyota Land Cruiser

1 Answer

1997 LANDCRUISER AWD AUTO. WHEN I PUT IT IN GEAR(DRIVE) IT GOES IN LOW. IT SHOWS LOW ON THE DASH AND DRIVE ON THE SHIFTER. WHEN DRIVING IT DOES NOT SHIFT OUT OF LOW.

Posted by on

  • hollett2 Oct 29, 2008

    1992 Land Cruiser AWD has the same prob,any specifics or solutions 1st and 2nd gear ok but drive slips

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Try positioning the gear lever at P positon , the remove the selector cable from the gearbox then push the selector mechanism til that it wont move, fit the cable back then try it out ....hope that it will help

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put gmc envoy in reverse and went to put in drive and dash says in drive but won't go into any gear


Check fluid level first. After that, many things inside the transmission could be the problem for no forward gear. Try manually shifting it to first or low. Could be the cable popped off the shifter arm on the transmission.

Aug 13, 2016 | GMC Cars & Trucks

1 Answer

2002 Nissan maxima stuck in 3rd gear, auto tranny . I was driving the other day to realize the light on the dash said I was in 3rd instead of drive, but my gear shifter was in the drive position ....


Most modern day autos are all electronically controlled, Usually if it detects a fault it can go into limp mode which by default is 3rd gear. The fact your speedo is not working which too is most likely sensor driven then that may be a clue to what is wrong. No speed sensor, no speedo and the transmission control unit is not getting the vehicle speed sense either. So it has no way of knowing what gear to be in or any shift points. I'm thinking it's a sensor issue would be my best guess.

Mar 23, 2013 | Cars & Trucks

2 Answers

I was driving my97 rangerover and came to a stop light and upon leaving thestop it wouldnt move dash computer says transfer case in neuteral i tried to put it in park and it made a sound as if it was not...


Hello Joey... Have you ever put your Rover into Low range? You might have accidentally bumped the shifter to the right and it started to select Low range, but it is in Neutral because the Low shift was interrupted. To correct this, with the engine off, but with the key on, select Neutral first. Then start selecting Low by putting pressure on the shifter towards the right(to engage low, the second set of gear/numbers). Keep pressure on the shifter until the dash shows a Low range light and is no longer beeping...now you are in Low Range. Next try to select High range by putting slight leftward pressure on the shifter. Keep pressure on it toward the left until it quits beeping and no longer has any gearbox, neutral, or low range lights (20-30 secs Max each way/Range, etc.) Then select park and try restarting the engine, if you hear any funky/grinding sounds shut it down and repeat above process. It should work on the first try, however, You may Try it a few times before giving up on it if you never use low range. The Low range shift solenoid is probably shot if you cannot get it back into High Range, etc. Good Luck, Brian

Jan 17, 2012 | 1997 Land Rover Range Rover

3 Answers

How do you use 4WD on a 1999 dodge durango?


there are 2 systems.
one is a part time system only.the 4x4 locks and is for ice mud and snow.Driving full time will damage the transfer case.The other system is a full time system and the selector says 2wd,4wd part time ,4wd full time and 4 lo. if in full time,it can be driven all the time even on dry roads.The full time is really an all wheel drive system.
the 4low is a very low gear and the main shifter has to be put in neutral and then the transfer case put in 4 low.attempting to put it in 4 low while in "drive" will make a gear grinding noise.
getting out of 4 low is the opposite.shifter to neutral and then put it in 2wd and then in drive.The newer durango has an electronic transfer case with a dial on the dash.The 2002 was available with 2wd,4wd,awd and 4 lo on a switch.The 1999 has the lever on the floor .

Feb 12, 2010 | 1999 Dodge Durango

2 Answers

How do I put my 09 Suzuki SX4 AWD in lock position ?


You have a switch down by the shifter, on the side. You simply toggle the switch to lock position. You don't what to do that on dry pavement. Just put the switch in auto. The computer will engage and disenage when needed. Don Suzuki guy

Oct 04, 2009 | 2008 Suzuki SX4

1 Answer

Tranny problem???????


Shifting Solenoid might need to be replaced.

Jan 20, 2009 | 1997 Ford Explorer AWD

2 Answers

Transmisson,


Check you linkage, go under your car and shifter by hand( with tool) at the trans. to first gear.and drive in first gear.

Jan 04, 2009 | 1997 GMC Jimmy

1 Answer

Transmission


Kragen can do it for free, plus others like auto zone

Oct 12, 2008 | 1996 Chevrolet Blazer

1 Answer

1997 engaged in 4 wheed drive


I HAVE THE SAME PROBLEM,UNCOUPLING THE BATTERY DISENGAGES THE PROBLEM,BUT I STILL DONT KNOW WHAT CAUSED IT.

Jul 14, 2008 | 1997 Ford Explorer AWD

Not finding what you are looking for?
2001 Toyota Land Cruiser Logo

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...