Question about 1996 Dodge Stratus

1 Answer

Brakes lights and rear turn signals want work

Posted by on

  • 1 more comment 
  • christinaree Aug 25, 2008

    brake lights wont work. is this how they are? 3157 3157 3057 top to bottom?

  • kabperry Aug 31, 2008

    Turn signals quit working.

    Hazzard lights do work!

  • Anonymous Sep 30, 2008

    my 1998 dodge ram 1500 4wd turn signals, hazzard and brake lights just stopped working. All fuses are okay and I even "swapped" a few to ensure they worked on other accessories etc. The OM or fuse box panel does not specifally identify a replacable part. Might it be the blue square or gray rectangular component in the fuse box? Otherwise, any help is apprecaited. (I do have a factory trailer hitch setup.)

×

1 Answer

It's the flasher

Posted on Nov 03, 2008

6 Suggested Answers

  • 255 Answers

SOURCE: My brake light and turn signal on the left don't work.

Hi, you have a bad bulb,....

Posted on Aug 17, 2008

  • 1 Answer

SOURCE: brake lights/rear turn signals

I had the same problem with my 1999 Yukon. The electric board needed to be replaced. Rust starts to build up and shorts out or blows the bulb. The dealership charged $73.60 for the part and I installed it myself (Saved $30).

Posted on Jan 05, 2009

  • 107 Answers

SOURCE: rear brake lights

they are seperate fuses and also has trailer light relay for tow package models , look for trailer light relay fuse , with key on check them all while your there , if fuse is good , swap with another relay , if that will not work , check bulb housing for melted terminals , lastly have body control module ckecked

Posted on Feb 19, 2009

  • 2 Answers

SOURCE: Brake light, Turn signal not working rear right 06' Focus

I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems

Posted on Aug 06, 2009

  • 1986 Answers

SOURCE: 1994 chevrolet pickup - brake light problems

There will be an electronic flasher module located under your dash near the steering column (don't know it's exactly location as it varies). It sounds like this unit may be faulty.

Posted on Aug 21, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

Third eye works no rear signal or brake lights


The high mount brake light gets its own signal from the brake light switch (on the brake pedal). Or at least the wire leaving the brake light switch will splice, one wire to the high mount brake light, and the other for the rear brake lights is routed through the turn signal switch, and coordinated there with the turn signal wires to the rear brake lights. The brake wires and turn signal wires share the same wire, and same filament in the bulbs. It is kind of complicated, but brakes applied with no turn signal, brake light wire goes from brake light switch through the turn switch and out to the bulbs. If brakes applied with turning signal, non blinking brake light wire goes from turn switch to rear light, while the turning signal wire will go through the flasher relay, and then to the rear light to cause blinking.

I hope that makes sense. It appears the problem may be in the turn signal switch for both the turn signals and the rear brake lights.

Mar 14, 2015 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

Window break light good but actual break lights not working


sounds like you have a bad turn signal switch.

If the third brake light is working than we know the fuse is good and the switch is good. The third brake light bypasses the turn signal switch. If the rear turn signals are working than we also know that the wiring from the switch to the rear bulbs is also good. The brake lights and the turn signals are on the same bulb so the turn signal switch is what determines if the bulb gets power from the brake light switch or from the turn signal flasher. If the switch is bad usually the first thing that stops working is the brake lights.

Typically you can wiggle, jiggle, pull, push on the switch lever with you foot on the brake and get the brake lights to work. Sometimes turning the four way on and off several times will also get the brake lights to work. If this is the case than a new turn signal switch will solve you problem.

If you have any questions let me know!

Oct 11, 2011 | 1997 Chevrolet Lumina

1 Answer

1998 chevy lumina: rear window brake light not working, left brake light not working, rear left turn signal not working


See if bulbs have burnt out in the left brake light and rear turn signal (one bulb if combined) and also rear center high mount brake light.

If the left turn signal has a slower speed than the right turn signal, this is a symptom of a bulb or bulbs burnt out.

Usually, the wiring is not a problem, but I would not rule wiring (or sockets) as a problem out.

Good luck on this repair.

Jan 19, 2011 | 1998 Chevrolet Lumina

2 Answers

Rear brake lights, rear turn signals inoperable. bulbs replaced and are working, simply not responding to brake or turn signal?


If the third brake light always works, then it is the turn signal switch. If the third brake light does not work, it is probably something else. The turn signal switch is in the steering column. You have to remove the airbag and steering wheel, take out all of the componets and replace the turn signal switch. Special tools are required and a moderate level of mechanical ability. Watch the airbag, it can go off and cause serious injury!!

Sep 24, 2010 | 2004 Chevrolet Malibu

2 Answers

Rear turn signals and brake lights out. Front signals and rear tail lights work fine.


the brake lights and the rear turn signals should be the same bulb check the bulbs to make sure they are not blown does your third brake light work if all brake light are out and the bulbs are good check the brake light switch on the brake pedal

Nov 04, 2009 | 1986 GMC C1500

1 Answer

REAR BRAKE LIGHTS DO NOT COME ONLY TAP LIGHT IS


Check for power at the turn signal switch. White wire comes from brake switch switch into the turn signal switch. The brake light switch is working because the high mount brake light is working..right? Do the turn signals work ok? if so, then the wiring is OK. The brake signal wires that come out of the turn signal switch are dark green(right) and yellow (left).

Oct 27, 2009 | 2001 GMC Safari

1 Answer

Left rear turn signal and brake light dont work


You have a broken wire to the turn/brake light portion of the light as they use the same wire. Or where the plug goes into the light assy could be bad. Torsion mount lights are horrible and you should think about replacing with a universal light that you can wire direct.

Feb 17, 2009 | 1997 Jeep Wrangler

6 Answers

No rear brake light / turn signals on 2001 Chevy Cavalier


The problem is the turn signal/headlight/hazard switch assembly on the steering column which the brake light wiring runs through. The part is easy to change and cost about $50 at most parts stores

Jul 05, 2008 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
1996 Dodge Stratus Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...