How do you pull out the fuel pump out of my tank??????

You must remove the fuel tank which is underneath the trunk. Here's the procedure for removing the pump.

REMOVAL:

1. Before servicing the fuel pump the fuel system pressure must be relieved.
2. Disconnect the negative battery cable.
3. Raise the car on a hoist.
4. Remove the fuel tank.
5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal.

NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.

INSTALLATION:

1. Push the fuel pump assembly into the attaching hose.
2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal.

NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.

3. Install cam lock over the assembly and lock by turning clockwise.
4. Reinstall fuel tank.

You must remove the fuel tank to replace the fuel pump.

1. Remove fuel tank.
   
2. Remove any dirt that has accumulated around fuel pump module retaining flange.
   
3. Turn fuel pump module locking retainer ring (#1)counterclockwise using Fuel Tank Sender Wrench 310-D006 and remove fuel pump module locking retainer ring.
   
4. Pull fuel pump module sender plate up out of fuel tank until locking tabs(#3) for fuel pump module are accessible. Reach through fuel pump module opening, squeeze both locking tabs together and remove fuel pump module from fuel tank.

The fuel pump is inside the tank, so pulling the tank is a reasonable way to get to it. You may be able to pull it from the top of the tank without pulling the entire tank, depends on how they put it in. I honestly don't remember pulling the tank on mine when the pump went bad.

The fuel pump is located in the fuel tank. You need to drain the fuel and pull the tank out from the car. Your fuel pump will look like this, the top is part of the fuel tank.

since carburetors were replaced by fuel injection, about 1991, just about all gasoline fuel pumps were moved inside the gas tank and are electric.

1. Remove fuel tank.
   
2. Remove any dirt that has accumulated around fuel pump module retaining flange.
   
3. Turn fuel pump module locking retainer ring (#1)counterclockwise using Fuel Tank Sender Wrench 310-D006 and remove fuel pump module locking retainer ring.
   
4. Pull fuel pump module sender plate up out of fuel tank until locking tabs(#3) for fuel pump module are accessible. Reach through fuel pump module opening, squeeze both locking tabs together and remove fuel pump module from fuel tank.
   

Fig. Fig. 1: Electric fuel pump-TBI engines

1. With the engine turned OFF , relieve the fuel pressure at the pressure regulator. Refer to the fuel relief procedure in this section.
2. Disconnect the negative battery cable.
3. Raise and support the rear of the vehicle on jackstands.
4. Drain the fuel tank, then remove it.
5. Using a hammer and a drift punch, drive the fuel lever sending device and pump assembly locking ring (located on top of the fuel tank) counterclockwise. Lift the assembly from the tank and remove the pump from the fuel lever sending device.
6. Pull the pump up into the attaching hose while pulling it outward away from the bottom support. Be careful not to damage the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull it out of the rubber connector.

1. Connect the fuel pump to the hose.

Be careful that you don't fold or twist the strainer when installing the sending unit, or you'll restrict fuel flow.

1. Install a new O-ring on the pump assembly and then position them into the fuel tank.
2. Turn the locking ring clockwise until its tight.
3. Install the fuel tank and connect the battery cable.

If you dont feel like dropping the tank and hassling with the hangers because they often break cut a hole in the bed of your truck over the tank where the fuel pump is but be careful not to hit the wires. dont cut the piece out completely cut it so you can pry it up to oneside

hi there,
this is to clear the idea,your fuel pump is located at inside you fuel tank.this is not easy job for replacement,have a precaution doing this there fuel inside your tank if you wanna do this or fix your self,you have to remove electical source by pulling out first the one pole or terminal of your battery.to prevent in any spark,using syphon pump,you can empty your fuel tank evacuate all fuel inside your tank before pulling out your fuel pump.figure showing fuel pump/
disconnect all electrical connection on fuel pump.have a nice day

The fuel pump is in the gas tank...
I haven't worked on this type of car before, but by the year Im guessing there probably isn't an access to it from the inside of the car... Chances are you will need to drop the tank and pull it out...
not fun...

relieve fuel pressure (pull fuel pump fuse run car until it quits,) siphon fuel from tank, drop tank, remove wires and hoses,fuel pump is in tank, to remove, use snap ring pliers to remove pump retaining ring, pull up on pump, be carefull not to damage screen or sending unit in tank when pulling out.