Question about 2003 Volkswagen Golf

1 Answer

Radio reset code

My radio needs to be reset. I have the code for the radio but when I switch it on it only says SAFE. can you please help me.
The Serl nr of the radio is: vwz4z3g1100046
The VIN nr of the car : AAVZZZ17Z7U018286
The code of the radio is 0133

As I said it only shows SAFE when I switch it on. Please please help.
Buks
buks@fempower.co.za
082 5783 174

Posted by on

  • miamiflorida Mar 10, 2009

    could you give me code for beetle vwz9z75135463

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you made 2 errors, the radio will locks up. You could pull out the radio for several day, or months, but never will reset this hard SAFE.
The solution is easier than you are thinking; "Just turn on the radio, and turn on the switch key, but don't run the car. Leave ON the car switch and ON the radio for one hour".
After it, you will be able to use your unlock code. (Holding Mode+Scan until SAFE change to 1000... )
Remember... you have just 2 oportunities to enter the right code

Posted on May 19, 2009

  • Toniks
    Toniks Oct 16, 2013

    hey. but my radio dosen have a ''mode'' THE SCAN its but mode no what to prees to remove the safe

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have an 2002 audi tt,radio on safe mode.need help please


did you check manual if there is radio code card ?
if you do not have it, you two choices either visit dealer and they will be able to obtain correct code for your radio or try to contact Panasonic and find out their repair shop for automotive radios they will be able to reset for you they even might disable the safe mode so in case power loss you will not have to re-enter again

Oct 13, 2014 | Audi A6 Cars & Trucks

1 Answer

How do I get a vw jetta 2008 out of safe mode 2?


Usually has to be left switched on in safe mode for several hours before the code can be retried.

Aug 26, 2014 | Cars & Trucks

1 Answer

I have the code to reset my radio on my 1998 Volkswagen Passat but it's not working. I know that there are buttons I need to push after I put the code it but I can't remember what to do. Help please.....in...


The sequence of programming for 1999 Volkswagen Passat radio is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.

For example: we have the security code "5079". Then:
3. By the no.# 1 key you will set up the first safe code digit. Push 5 times on the no.# 1 button. The "5" number will be setted.
4. By the no.# 2 key you will set up the second safe code digit. Push 10 times on the no.# 2 button. The "0" number will be setted.
5. By the no.# 3 key you will set up the third safe code digit. Push 7 times on the no.# 3 button. The "7" number will be setted.
6. By the no.# 4 key you will set up the four-th safe code digit. Push 9 times on the no.# 4 button. The "9" number will be setted.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!


Please do rate my response. Thanks!

Feb 27, 2011 | 1999 Volkswagen Passat

2 Answers

How do you reset a 1999 Audi radio code Read more: http://wiki.answers.com/Q/How_do_you_reset_a_1999_Audi_radio_code#ixzz1BBivzkQU


IMPORTANT NOTE: You must have the security anti-theft code for your Audi radio from the car manufacturer, or from an Audi dealer!

The sequence of programming for Audi radio is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
3. By the #1 key you will set up the first safe code digit.
4. By the #2 key you will set up the second safe code digit.
5. By the #3 key you will set up the third safe code digit.
6. By the #4 key you will set up the four-th safe code digit.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!
Please do rate my response. Thanks!

Jan 16, 2011 | 1997 Audi A8

1 Answer

I have passat 1.9 tdi variant,2001. year.my batery is dead.when i take a new batery i was missing code for radio in car.type of radio is vw gamma.when i switch radio on, on the display write safe.please...


How to exit the 1998 VW Passat radio out of SAFE mode:
IMPORTANT NOTE: You must have the security anti-theft code for your VW radio from the car manufacturer, or from a VW dealer!
The sequence of radio programming is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
3. By the #1 key you will set up the first safe code digit.
4. By the #2 key you will set up the second safe code digit.
5. By the #3 key you will set up the third safe code digit.
6. By the #4 key you will set up the four-th safe code digit.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!

Dec 05, 2010 | 1999 Volkswagen Passat

1 Answer

How do you enter code to reset 1999 A4 Audi 2.8 Quattro Radio ? Needs help. Please.


IMPORTANT NOTE: You must have the security anti-theft code for yours Audi Concert radio from the car manufacturer! For Audi Concert Radio the sequence of programming is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
3. By the #1 key you will set up the first safe code digit.
4. By the #2 key you will set up the second safe code digit. 5. By the #3 key you will set up the third safe code digit.
6. By the #4 key you will set up the four-th safe code digit.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!

Sep 16, 2010 | 1998 Audi A4

1 Answer

VW radio


"2 safe" means that you have entered the wrong code twice. Leave the igniton switched on for about an hour and it will reset to - - - (three small lines) then you can enter the correct code. If you dont have the code you will need to speak to your vw dealer

May 29, 2009 | 1998 Volkswagen Beetle

10 Answers

Vw passat radio code


Passat 97 need to re-enter code ( 4 ) digit, however it shows the number 2 on the on screen when the radio is turned on.
Help. I need to know the steps to reset. thanks

Dec 13, 2008 | 1999 Volkswagen Passat

3 Answers

2000 Audi A4 Radio Problem


I agree with Guest - he's got all the info straight.

Jul 02, 2008 | 2000 Audi A4

Not finding what you are looking for?
2003 Volkswagen Golf Logo

Related Topics:

1,090 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...