Question about Chevrolet Celebrity

2 Answers

Windshield wiper problems 1989 celebrity juice at the motor and either side of fuse is the a relay that could be bad if so where is it located

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Check the GROUND for the WIPER MOTOR, and Wiper motors do wear out

Posted on Aug 13, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 183 Answers

Hi, if your saying that you have 12 volts to the motor and it still doesnt work,then replace the motor...Good Luck!!!

Posted on Aug 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

I'm driving in rain, wipers working good, all of a sudden they quit! I drive for 15 min, check again, they work for a while, then quit again...what in the problem?


If your not familiar with automotive electronics an module control of components , I suggest you take it to the dealer . They have the tools to diagnose this type problem !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper PCB relay


?€¢
Wiper high PCB relay


?€¢
Windshield wiper motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
WPR fuse 25 A


?€¢
WSW fuse 10 A


Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
High Speed Operation When the wiper switch is in the high speed position, ground is applied through the windshield wiper switch high signal circuit to the body control module (BCM) indicating the wiper high speed request. In response to this signal, the BCM then energizes the wiper PCB relay, as stated above, and the wiper high PCB relay by applying ground through the control circuit to the coil side of the relay. With the wiper high relay energized and its switch contacts closed to the high speed control circuit of the wiper motor, the motor will operate at high speed.
Wiper motor high speed operation and the wiper high speed PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
You could Have a switch problem , BCM problem ,PCB relay problem , the pcb relays are non serviceable an the whole under hood fuse box would need to be replaced . Malfunctioning motor bad ground some where etc.....

Dec 20, 2015 | 2008 Chevrolet Impala

2 Answers

2000 toyota camry windshield wipers won't work


First I would look in the fuse box by the driver side and check the fuse,if good then get a meter and see if power is going to wiper motor,if so,then wiper motor is bad,if no power is going to motor,then bad switch,here's a link to see. Repair Guides Windshield Wipers And Washers Windshield Wiper Motor...

Windshield Wiper Switch

Print
REMOVAL & INSTALLATION
The windshield wiper/washer switch is part of the Combination Switch Assembly. Refer to Turn Signal/Combination Switch services procedures.

Oct 18, 2014 | 2000 Toyota Camry

2 Answers

Windshield wiper relay


no the relay will be located in a box mark relay or fuse open box look at top a daghme will show witch relay is the wiper

Sep 02, 2014 | Cars & Trucks

2 Answers

Windsheild washer motor will not work.


Windshield Washer Pump

1990 Ford Truck F150 1/2 ton P/U 2WD 5.0L FI 8cyl

The Windshield Washer Pump is located: Under hood, driver side front side of wheelwell, mounted inside washer bottle.here's the part. TAAP Windshield Washer Pump 7 664 1990 Ford F150 1 2 ton 2WD 8...

Jan 14, 2014 | 1990 Ford F150

1 Answer

Replacing wiper linkage


WINDSHIELD WIPERS


It can be faulty wiper motor or blown wiper control fuse.


Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring: -----

For complete troubleshooting i suggest you few helpful links with accurate solutions.

-------------

Click the link below: -------


1993 Ford F350 wipers not working?

http://repairhelpcenter.blogspot.in/2012/02/1993-ford-f350-wipers-not-working.html

------------

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

------------

Wipers not working, but hear relay click on Lincoln LS?

http://schematicsdiagram.blogspot.com/2011/12/wipers-not-workingbut-hear-relay-click.html

-----------

Car windshield wiper gets power for movement and stops?

http://schematicsdiagram.blogspot.com/2011/12/car-windshield-wiper-gets-power-for.html

----------

How does cars Windshield Wiper System Works

http://technoanswers.blogspot.com/2011/11/how-does-cars-windshield-wiper-system.html

---------

1997 Honda Protege: Replace Wiper Transmission?

http://technoanswers.blogspot.in/2012/06/1997-honda-protege-replace-wiper.html

----------------

Windshield wiper fluid container leaking?

http://whatisbyme.blogspot.in/2012/05/windshield-wiper-fluid-container.html

-----------------

Where is wiper fuse located on1993 chevrolet suburban

http://technoanswers.blogspot.in/2012/02/where-is-wiper-fuse-located-on1993.html

------------

2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?

http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html

-------------

Complete wiper components replacing details for Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/complete-wiper-components-replacing.html

------------

These details will help.

Thanks.

Nov 29, 2012 | 2003 Chevrolet Cavalier

2 Answers

Windshield wipers work on high only 03 malibue


Most likely the cause of this is because of the switch not operating properly. The wiper switch circuitry has 3 different diodes. One for high, one for low, and one between the 2 relays that run the motor. One relay turns the juice on and the other determines if it's high or low speed. On/off is relay 39, high/low is relay 40. You'll find them under the hood. Lift off the battery cover, then the fuse block cover. On the underside of the fuse cover is the location legend. The diode is #27. Check it for pass/no pass with a small light while unplugged from the circuit. Also try swapping the two relays with each other. This will determine if the problem is the switch.

Jan 18, 2012 | 2003 Chevrolet Malibu

1 Answer

I changed the relay fuse to my windshield wipers and the knob and my wipers still wont work on my 98 plymoth grand voyager what should i check


Turn wipers on (veh in "on" or "acc" position)
Disconnect the electrical connection at the windshield wiper motor (located in the engine compartment on the fire wall) and check for voltage. If you have voltage, there is a good possibility your windshield wiper motor is bad.
You may also: Disconnect the electrical connection at the windshield motor and run a heavy gauge wire directly from the positive side of the battery to the motor. If you get the windshield motor to come on. There may be only a wiring (short) problem between the relay and the motor.
Let me

Jan 21, 2010 | 1989 Plymouth Reliant

1 Answer

Replacing the windshield wiper on a 1989 Celebrity


The clip should lift up and then the pin should allow the blade to come off, you should have to use slight pressure on one end or the other

Oct 24, 2009 | 1989 Chevrolet Celebrity

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...