Question about 1994 GMC Jimmy

1 Answer

Cant get key out of ignition - 1994 GMC Jimmy

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There is a hole underneath the stearing wheel. You take out the piece, and stick a pen/rod in there and then turn the ignition to the off switch. If you have absolutely no power in the vehicle and your key is stuck. I recommend cleaning the two way fuse located just beneath battery. My vehicle ran just fine afterwards.

Posted on Aug 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Something wrong with my ignition what could be wrong


sounds like the ignition key switch is worn and needs replacing.

Sep 07, 2014 | 1997 Mitsubishi Galant

1 Answer

2010 Malibu key wont go into ignition switch


The tumblers may have collapsed. In which case you would have to replace the switch. They can be replaced if you can get the key in.. If you get a replacement you can try forcing it, if it locks up you will have to drill it out to get it replaced.

Jun 17, 2013 | 1999 Chevrolet Malibu

1 Answer

How would you hotwire a Mazda b2300 if u lost the key.


cant hotwire your vechicle has the PATS SYSTEM.your keys has transponder on it.the ignition switch antenna ring and immobilizer control module and ECM read signal emitted from the keys transponder if you have no keys or wrong keys the PATS SECURITY SYSTEM DISABLE IGNITION SYSTEM CAR WONT CRANK.CANT HOT WIRE CAR WITH THE PASS KEY SECURITY SYSTEM.older cars back in 70s you could hot wire newer cars you cant.

Apr 05, 2013 | Cars & Trucks

1 Answer

Cant put key in ignition


Somebody tried to steal your car maybe? Sounds like you need to replace the ignition lock cylinder.

May 26, 2012 | 2005 Buick Rendezvous

2 Answers

Cant get my key out of the ignition, everything works fine, just cant get the key out.


these puppies are notorious for that.

Did you try some panther ****? (i.e. wd-40 or PB Blaster into the ignition switch?)

for better results limit your number of keys attached to the key ring going into the ignition switch to a maximum of two or three..

Best regards
Ck

Aug 18, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Cant take key out of the ignition in a volkswagon passat 2003.


Try and move the steering wheel around while you remove the key. It may have it locked in place.

Jan 13, 2010 | 2003 Volkswagen Passat

1 Answer

My 1997 audi a4 the ignition key is stuck. what


OK first thing- Car has to be in park to pull the key from the ingnition. if it is and you still cant pull it, rock the wheel back and forth alittle (sometimes the columb lock doesnt lock properly and you cant release the key until it locks, rocking the wheel usually fixes this problem). and the last possibility is that the tumblers in your ignition have broken, when this happens you cant pull the key from the ignition because you cant turn the key back to the off possition all the way. when this happens you don't want to pull the key because you risk not being able to put it back in the ignition later and are forced to replace the ignition so you can drive your car. However if the tumblers are indeed broken you will have to replace the ignition anyway, atleast by leaving the key in it you can still drive the car until its replaced

Dec 27, 2009 | 2001 Audi A4

1 Answer

I cant turn the ignition or move the steering wheel on my 2003 nissan altima. When I insert the key I get the usual sound but I cant turn the key at all, and the steering wheel seems like its stuck.


i think there is a ignition problem , might try replacing it , of course you cant turn the steering if the key wont turn , its a theft prevention device.

Oct 02, 2009 | 2003 Nissan Altima

1 Answer

Ignition switch locks and it cant be cranked


your key may overly worn and replaced, try jiggling the key and steering wheel at the same time. if that doesnt work try sraying a penetrating oil, like WD40 or PB Blaster, into the lock cylinder. it could also be the shift knob safety switch not disengaging or a faulty ignition switch

Nov 30, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
1994 GMC Jimmy Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...