Question about 1996 Chevrolet Cavalier

1 Answer

Head Lights My low beems won't work,the high beems work fine.The Bulbs are good,the realy is good the switch is good?????????????????????????

Posted by on

  • yok225 Aug 16, 2008

    My driver side high beam works, but the passenger side does not nor do either one of the low beams. Any thoughts?



  • Anonymous Mar 24, 2014

    when wiring the lights. are the low beems on top

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 243 Answers

Check the continuity of the headlights to make sure there switching from the DTR Lights to the highbeams. If you are not getting the proper continuity check the ground wire for the low beams to ensure its properly grounded and has proper continuity throughout the wire. If not replace the wire or tighten as required and that should fix your problem.


lemme know if you require further assistance,

thanks - Nate

Posted on Aug 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Front head lights quit working high beems work low beam doesn't new bulbs and fuses are good for both sides can anyone help? Been working on cars for years can't figure this one out


Could be dirty or burned dipswitch contacts. If the driver smokes this is not uncommon.

I suggest exposing the multiplug to the dipswitch and bridging the terminals as required to bypass the switch.

Jan 23, 2016 | 1996 Ford Explorer

1 Answer

The headlight on the pass. side works right. the drivers side when in low beem, the light is in high beem. when the light is on high beem the light is on low beem. this is a 2000 mercury sable


someone has switched the wiring harness sockets to the wrong bulbs or installed the bulbs in reverse. get in behind the headlight assembly on the driver side and reverse the wires, if that does not work then pull the bulbs and swap them inside to outside and vice versa.

Jun 10, 2011 | Mercury Sable Cars & Trucks

1 Answer

1998 Camry Low beams work fine but when i switch to high beam i loose all lights


the relay for your highbeem lights is bad, replace it and you should be good, or you could just switch the high beem relay, with the low beem relay, they are the same, and if the high beems work like that you know its full proof, if not... well you know, we will hafta move to something else.. hope you find this helpful

Dec 04, 2010 | 1998 Toyota Camry

1 Answer

Head lights and brake lights not working


check power wire which runs to the brakelight with a test light, get someone to apply the brake on and off and see if there is power getting back to that point, if no power check the switch on the brake pedal to see if power is getting to that point.
also check the earth on the bulbs because they wont work if there is no earth

Jun 09, 2010 | 1987 Volvo 240

1 Answer

Head light do not work but the high beams will


This is a common problem. You didn't mention the type of vehicle you have and whether or not its one or both bulbs. At any rate, first make sure the bulbs are not blown, the head light fuses are not blow and that the headlight connectors are on. If all of those things are good there maybe a problem with the wires or the dimmer switch may have failed. You may need a wiring diagram to follow up with. I know that you will say that because the switch still activates the high beems, how could it have failed. The reason is because power for the low beams often travel thru this switch. Often times, this portion of the circuit can fail.

Apr 20, 2010 | 1999 Ford Windstar

3 Answers

Low Beems are out. I changed both bulbs and the


DIMMER SWITCH OUT OF ADJUSTMENT.I SEEN CAR WITH SAME PROBLEM THEIR HIGH BEAMS WOULDNT WORK.THE DIMMER SWITCH AND BULBS WAS GOOD.IT TURNED OUT TO BE DIMMER SWITCH NEED TO ADJUSTED.

Mar 21, 2010 | 2005 Chevrolet Monte Carlo

1 Answer

2005 Trailblazer, Low beems will not work high beems do


Pull plastic cover off of column ck where wires mate to multi function switch and switch for traces of heat . More than likely switch is bad.

Jun 16, 2009 | 2005 Chevrolet Trailblazer Ext

2 Answers

Fuse is fine hazards work but turn signals do not. all new bulbs.


your flasher is probably bad, it is usely round and mounted close to the fuse box

May 02, 2009 | 1988 Chevrolet Beretta

1 Answer

Low-beams not working on 2008 Ford 150


Basicly lights operate from same source of power, so if you have high beems then power and ground should be intact. The operation of changing high to low is controlled by column switch,< blinker switch assembly >, and there slight possibility that both bulbs are actualy bad. To be on the safe side would check bulbs and wiring to them is in good shape before trying switch replacement.

Apr 22, 2009 | 2008 Ford F-150

Not finding what you are looking for?
1996 Chevrolet Cavalier Logo

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...