Question about 1994 Chevrolet C/K 2500

1 Answer

I CANNOT FIND THE CAM POSITION SENSOR ON MY MOTOR

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you have a chevy v8 up to 1998 (gen I/II) there is no cam sensor.

Posted on Aug 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my camshaft position sensor located on a 2008 chevy aveo


It should be located between the cam shafts. If you remove the Beauty Cover (( that's what they call the cover across the top of the motor. )) And then the Valve Cover. The Cam Sensor will be sitting between the Cam Shafts. Closer to the Intake Cam Shaft.

Aug 16, 2014 | Cars & Trucks

1 Answer

Code po340,change coil,cam sensor,still got code,missing


that is the code for cam position. . when you replaces the sensor did you clean the cam,and replace the seal. what motor do you have

Dec 09, 2012 | 1996 Chrysler Town & Country

1 Answer

98 caravan 2.4 0340error code


P0340 DODGE - Camshaft Position Sensor Circuit Bank 1 Sensor 1

Possible causes- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery Tech notes Sometimes and in some models, low battery voltage or a weak starter can can trigger a Camshaft Position Sensor code, also a loose worn cam belt can cause this code. Has the belt ever been replaced?.

Oct 10, 2012 | Dodge Caravan Cars & Trucks

1 Answer

Got code po340 on 2008 Chrysler PT cruiser. Runs great sometimes when engine light on & rough at other times like not getting gas. Engine light does not come on every day either. Cam sensor or timing...


P0340: Camshaft Position Sensor A - Bank 1 Circuit Malfunction

- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Feb 08, 2012 | 2008 Chrysler Pt Cruiser

3 Answers

My 2004 Taurus has chirping sound in motor.Not belts.Other end of motor.Could it be cam position sensor?


YES. Very common problem. The cam sensor driver unit goes bad. (Usually called a "Cam Syncronizer") Squeeks like crazy, causes hard starts, poor fuel mileage, usually destroys the cam sensor itself, and will cause catalytic converter damage if not fixed promptly. (You will find broken, rusted pieces inside the assembly if you take the sensor off of the top)
Complete kits (Made by Dorman) are available at most parts retailers. It will look similar to this:

dttech_10.jpg It should be noted that although this part is relatively easy to replace, it can also be very easy to install it incorrectly. Proper alignment (Syncronization) should be checked using a scan tool after installation.

Apr 24, 2011 | 1999 Ford Taurus

1 Answer

Where is the crankshaft positioning sensor


If you have a 2.8L V-6, it is at the lower end of the cam spindle (actually in the motor). The CAMshaft position sensor is at the top of the spindle (you can actually see it on the outside of the motor)

Apr 03, 2011 | 2001 Volkswagen Passat

1 Answer

2001 dodge 3500 van cam position sensor location


Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.

Jul 25, 2010 | 2001 Dodge Ram 3500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...