Question about 2004 Mitsubishi Endeavor

Open Question

2004 Mitsubishi Endeavor Radio

Hello,
My radio in my Endeavor isn't working properly. I cannot use the preset station buttons at all, I cannot scan, however I can use the up seek arrow (not the down). I cannot push the tune button in to change the station, or to turn the bass, fading, etc either. Recently I replaced the battery, and now it only offers AM radio or I can listen to a CD as long as I don't skip to another song, if I do that it acts like the CD is skipping. I can eject the CD. Basically the only buttons that are working are -
Volume
Up seek arrow
Eject CD button

Would this be something that perhaps a fuse has blown? Any help would be great as I am not finanicially ready to have a specialist look at it and charge me an arm and a leg. Feel free to email me at - lshelly312@hotmail.com or here, thanks!!

Posted by on

1 Suggested Answer

  • 7353 Answers

SOURCE: I purchased a 2004 Mitsubishi

most cars you just tune the station you want, then hold the preset button (that you want the station at) in until it beeps .

Posted on Sep 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to program the radio in a 96Lincoln continental after battery was disconnected


Hi,

Here is the link to the owners manual which you can download if you wish:

http://owner.ford.com/servlet/ContentServer?pagename=Owner/Page/OwnerGuidePage&year=1996&make=Lincoln&model=Continental

Here/below are the specific instructions on the radio programming (pg. 159 of above link).


Good luck & please flag if "HELPFUL". Thanks!

(from section) Luxury Audio System


Selecting the AM or FM frequency band

Push the "AM" or "FM1/FM2" button to select the desired frequency band. Pushing the "FM1/FM2" button more than once will alternate between FM1 and FM2. These functions are used with the station memory buttons described under How to tune radio stations.

HOW to tune radio stations

There are four ways for you to tune in a particular station. You can use the "TUNE", "SEEK", 'SCAN"or memory buttons.

• Using the "TUNE" function:
You can change the frequency up or down one increment at a time by Pressing and releasing either the left (< arrow/up) or - right (> arrow/down) side of the "TUNE" or "TUNE DISCS" button. To change frequencies quickly, press and hold down either the right or left side of the button.

Manual tuning adjusts your radio to any allowable broadcast frequency, whether or not a station is present on that frequency. (See All About Radio Frequencies in this section.)

• Using the "SEEK" function
: Press the right *) side of the "SEEK" button to select the next listenable station up the frequency band. Press the left (.4) side of the button to select the next listenable station down the frequency band. By holding the button down, listenable stations can be passed over to reach the desired station. Pressing the "SCAN" button will begin the scan mode up the frequency band, stopping on each listenable station for approximately five seconds. To stop the scan mode on the presently sampled station, press the "SCAN" button again.

Setting the station MEMORY PRESET buttons
: Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FMI and 6 in FM2)

1. Select a band, then select a frequency.

2. Press one of the memory buttons and hold until the sound returns and the lamp above the memory button lights up. That
memory button is now set.

3. Follow the above steps for each memory preset button.

NOTE:
Custom memory presets can be recalled using the keyless entry system. See Memory Profile System in the Features chapter.

Using the Automatic Memory Store feature ("AUTOSET")
: If the memory buttons have been set, either by using the Auto Memory Load feature or if you have set them manually, the system is prepared tolet you use a convenient feature called Automatic Memory Store.

With Auto Memory Store, you can continually set strong stations into your memory buttons without losing your originally set stations. Your radio will automatically set your memory buttons to the strong local stations.

Activate Auto Memory Store by pushing the "AUTOSET" button once. Your radio will set the first six strong stations of the band you are in (AM, FMI or FM2) into the memory buttons. The display will flash "AUTO" and display the autoset icon "A" while the stations are being set in the memory buttons.

NOTE: If there are less than six strong stations in the frequency band, the remaining unfilled buttons will store the last strong station detected on the band. After all stations have been filled, the radio will begin playing the station stored on memory button 1.

To deactivate the Auto Memory Store mode and return to the manually-set memory button stations, simply push the "AUTOSET" button. Display will show "AUTO" then "OFF". The next time Auto Memory Store is activated on that band, the radio will store the next set of six strong stations.

Nov 23, 2014 | 1996 Lincoln Continental

1 Answer

How do I get my radio to work after I changed my battery. I have the radio code. It is a 2004 Suzuki forenza


Hello there

I found this in a suzuki forum

After connecting the audio security system to the battery, "CODE" will flash on the display.
Enter the proper security number into the unit, using the preset buttons No. 1 through 8.
For example, if the security number is "1234":
Press the preset button No. 1. "CODE" will disappear and "1 --- " will appear on the display.
Press the preset button No. 2, and "12 -- " will appear.
Press the preset button No. 3, and "123- " will appear.
Press the preset button No. 4, and "1234" will appear and flash three times.
The audio system will function and will transfer to the radio. If the incorrect security number is XXXXX into the unit, "Err" will appear followed by "CODE" and there will be several audible beeps. If this happens, repeat the security entering procedure beginning with Step 2.

Hope this helps.
If code doesnt work then it is dealer, sorry.

Sep 24, 2014 | Cars & Trucks

1 Answer

How to find the radio code for 2004 Mitsubishi Endeavor radio has no sound after replacing dead battery


Depending on the make you can go online, search the make/model/serial number on specialist website that will sell you the code for a couple of bucks. As you didn't provide this in your question I couldn't test run it for you. Serial number may be in the drivers book or remove radio and it will be on the back. Has nobody written it in the owners books anywhere? Next time hook up a small motorcycle battery to your main batt leads before you remove the main batt and this will keep the codes in place while you swap the main batt.

Sep 05, 2014 | 2004 Mitsubishi Endeavor

1 Answer

How do I manually set my radio stations to my rcart2770 reciever


1. Connect the FM antenna and the AM loopantenna at the back of the unit. Rotate the AM loop for better reception.
2. Press AM/FM.
3. Tune a station by pressing TUNER+/-repeatedly until the desired station is found.Alternatively, you can press and hold thesame buttons down for about one second toactivate the automatic search function. Inthis mode the unit will automatically tunefrequencies until it finds a station.
4. Repeat step 3 to tune to another radio station.
5. Press AM/FMto select between FM and AM.Storing Radio Stations

The unit can store up to 40 radio stations (30 preset stations for FM and 10 preset stations for AM) in its memory. You can enter every single radio station yourself or the unit can store all available radio stations automatically in ascending order

Automatic Preset Programming
1. Press AM/FM to enter the AM/FM mode.
2. Press and hold AM/FM for two seconds to start automatic preset programming.
3. Radio frequencies will be browsed and radiostations stored automatically. When all the available radio stations are stored or all 40(30 preset stations for FM and 10 preset stations for AM) memory locations are full,the auto preset programming function will stop.

Manual Preset
1. Tune to a radio station (see "Manual tuning"for details).
2. Press MEMORY. While the Program Preset number is still flashing, input your desired preset number using the numeric buttons or press CH+/-, then press MEMORY to store it.

Retrieving Preset Stations
1. Press AM/FM to enter the Tuner mode.
2. Press CH +/- to search up or down for thepreset stations or directly press the numeric buttons.

Apr 30, 2014 | Cars & Trucks

1 Answer

Radio stations


There is a radio option to recalibrate your touch screen. Please press the following three hard keys simultaneously RADIO/MEDIA, SEEK UP, NAV (AUDIO on REN). Once you begin to recalibrate the touch screen you must finish. Audio confirmation prompts are provided for each of the three points of calibration, one beep for the first, two for the second and three for the third. The calibration needs to be precise as possible and a PDA stylus would be recommended. The MyGIG radio requires the user to repress each calibration point to confirm the calibration process. A green crosshair indicates proper calibration.You must not start with the "+" but with the "+1", then goto "+2" and last to "+". Repeat this until all crosses are green and exit with pushing the menue or any other key. Done

Jul 20, 2012 | 2008 Dodge Grand Caravan

1 Answer

Daughter has 1998 beetle, no owners manual the radio is in the safe mode and not coming on vin 3vwbb61c61c6wm010615, how do i get this to work?


Hello Camille, you will need the code for the radio, if you don't have it, look in the trunk, VW likes to hide them in there, under the spare tire. If you can't find it, you will have to get it from the dealer per VIN number. Once you have the code follow this procedure.

1: Turn on the radio, "SAFE" will appear in the display
2: After 3 seconds, the number 1000 will appear in the display.
3: Use the radio station preset buttons 1 to 4 to enter the code number for your radio. Use preset button 1 to enter the first digit in the code number. Use button 2 to enter the second digit, etc. The value range for each of the 4 digits is "0...9". The digit will increase by 1 each time you tap the preset button. The number returns to "0" after "9".
4: After you finish entering the code, press the right side (">") of the SEEK button 10 for longer than 2 seconds until you hear an audible signal.
5: if you`ve entered the code number correctly, "LSM" will appear in the display.
6: Now you are ready to use the radio again.

I hope this information is helpful.


10_8_2011_10_27_28_pm.jpg

Oct 04, 2011 | 1998 Volkswagen Beetle

1 Answer

I purchased a 2004 Mitsubishi Endeavor without an owners manual and i don't know how to change the radio station presets!


most cars you just tune the station you want, then hold the preset button (that you want the station at) in until it beeps .

Sep 05, 2011 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

71694 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7031 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...