Question about BMW X3 Series

2 Answers

My key fob has stopped working. - X3 Series BMW Cars & Trucks

Posted by on

  • 2 more comments 
  • GEDNOBLE Aug 21, 2008

    YEH ME TOO. WONT ACTIVATE C/LOCKING AND OF COURSE ALARM KEEPS GOING OFF. SIREN IS DISCONNECTED BUT LIGHTS KEEP FLASHING SO NOT ABLE TO DRIVE SAFELY.GED

  • Anonymous Sep 27, 2008

    Same problem. New battery in fob.

  • debnwarren Oct 05, 2008

    i have a 2002 bmw 525i and my key stopped working as far and the alarm and the locking of the doors. how do i open up the key to change the battery and once i do that, is there anything i have to do?



    Debbie

  • Anonymous Mar 27, 2009

    2004 BMW, the key fob stopped working. Can;t remotely lock or unlock doors.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

Have you tried replacing the batterys in it? and if you have you will need to inisalise the key. if you need to know how just ask again & i will post the whole process.

Posted on Aug 22, 2008

  • jdjohnson99 Nov 10, 2010

    How do you inisalise the key?

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My bmw x3sereis ramot batery is daed i need to change ti how can i open it

Posted on Feb 17, 2009

4 Suggested Answers

  • 32 Answers

SOURCE: Key fob stopped working the door locks. I changed

the circuit boards on those factory remotes, sometime break where the battery is clipped in, check to make sure the solder is holding the clip properly and it is not loose, also they remote may need to be programmed to the vehcile with a scan tool, usually only found at GM, Also the rubber part of the remote on the inside where the pad touchs the circuit board, uses a small screwdriver and touch the exposed circuit, if the remote locks the doors, try putting in tiny peice of alumumn tape of the inside pad, the connectiveness of the rubber wears off. If not try above or dealer.

Posted on Oct 02, 2009

  • 1 Answer

SOURCE: My key fob has quit

Mine did the same thing. I put the fob into the reprogramming slot located in the center console and was able to get it started by leaving the in the slot. Hope it works for you.

Posted on Sep 17, 2011

  • 279 Answers

SOURCE: remote key fob stopped working not battery

Follow the instructions on http://www.bluejag.co.uk I would normally cut and paste the details but you can't do this now, so sorry.
Don't go to Jaguar dealership unless you have cash to waste, and the turn 8 times solution may well work but is incorrect. There are other things that you need to be aware of (all explained on the website)

Posted on Apr 22, 2012

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both key fobs stopped working for 2010 Rav4


I would be contacting dealer service for reprogramming...good luck

Jan 27, 2013 | Cars & Trucks

1 Answer

What caused my '05 mazda 6 key fobs to stop working


Loss of programming maybe or a faulty keyless entry module.

Nov 01, 2012 | 2005 Mazda 6

1 Answer

Key fob stopped working


sounds like the key fobs have screwed up _ they could need re-setting but l would call a dealer to find out more info

Sep 13, 2012 | Chrysler Town and Country Cars & Trucks

1 Answer

My key fob stopped working overnight x type jaguar 2002


pop open the key fob from the side and you will notice a watch battery inside the fob, replace it and make sure nothing came unsoldered from the board and that should fix the problem

Nov 23, 2011 | Cars & Trucks

1 Answer

Remote control has stopped working. Have tried changing the battery of the remote control but that did not work.


Does the red light on the remote light up when you push any of the button
if no, replace remote
if yes, then try repograming the remote to the car again.
-Have remotes' ready. if you have two then fob#1 and fob#2 (doesn't matter which one is #1 or #2)
-each step has to be done within 5 sec or it will not work, but don't do it super fast.
1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
2.turn key off
3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
4.turn key off
5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
6turn key off
7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 8)and push the "lock button" on fob#2 twice.
8.turn key off and remove key from ignition.
if you did it right, remotes' should work again.
good luck

Dec 17, 2010 | 2003 Honda Accord

1 Answer

Key fob 2001 jag s-type stopped working. not battery


Your car has a module for the FOB , that could need to be replaced and programmed , or just to reprogram keys again

Jun 21, 2009 | 2001 Jaguar S-Type

1 Answer

Key fob on my audi a3 1998 has stopped working


the problem is inside the key fob if there is no response from the key fob at all then a new one will be needed. the problem is in side there is a mini circuit board in which all the sensors for that specific car are soldered on they can break very easly.

Jan 03, 2009 | 2005 Audi A3

1 Answer

Do key fobs loose memory (06 Pontiac Grand Prix)


do you have the owner manuals .... it tells you how to program them for that car

Dec 11, 2008 | 2006 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,073 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...