Question about 2000 Hyundai Accent

2 Answers

Brake Bulb I have an Hyundai Amica - Reg 2000 and need to change the brake bulb as it does not work. I have lifted the boot up but I am unsure whether I need to take the lens off or take the large casing inside the boot off to do this

Posted by on

2 Answers

There are three philips screws which hold the lense onto the body work, remove this carefully, and the turn the holder out and remove the bulb. refitting is in reverse order.

Posted on Sep 14, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

You should be able to get to the bulb from the trunk.

Posted on Sep 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i change the rear brake light of a hyundai accent model 2000


Hi, You will have to pop the trunk open and pull some of the carpeting away to acsess the light assembly. Then just turn the socket and the bulb should come out. Replace with same bulb size and watts. Good luck.

Feb 24, 2012 | Hyundai Accent Cars & Trucks

1 Answer

Brake lights not working. Turn signal flashes quickly like it is burned out but still working. Fuses all look ok


there is normaly more than one bulb, one for your blinker and another for you brakes. you should just have to change out the one bulb and it should be fine.

Nov 04, 2010 | 2000 Hyundai Elantra

2 Answers

How to change brake lights on my 2007 toyota yaris


on either side of the boot interior, there are what look like air vents. these clip out from the top (with a flat screwdriver) you then unbolt the light unit, pull it out. the bulb holder then unclips easily.

Jul 13, 2009 | 2007 Toyota Yaris

1 Answer

High Level Brake bulb replacement


If memory serves, there are two screws holding this light assy to the rear package deck. They are covered (LH and RH side of this assy). remove the covers and using a phillips screwdriver, remove the screws and lift the assy up and away from the rear glass. you now have access to the bulb and socket.

May 18, 2009 | Hyundai Motor 2004 Accent

1 Answer

Front side light replacement


inside behind the headlight there are twist off caps just twist them off and your in/ Please rate my response thank you very much

Feb 02, 2009 | 2000 Hyundai Accent

1 Answer

Hyundai amica 2002 reg - when the car get warm the engine dies


kindly check Battery, if battery is good. then try Push starting it, if the probelm is solved, take the vehicle to garage it might be problem of a PIV Sensor, of Starter motor must be weak or check any back compression is started in your car, if it has started then...

Dec 21, 2008 | 2002 Hyundai Accent

2 Answers

Brake lights


hi from uk not too sure on elantra but will try to help? if car is hatchback ? lift up hatch and look at the water drain channel alongside lamp? if there are 3x screws? unscrew and lift lamp off then unclup bulb/lamp board from lens bulbs are bayonet fitting if saloon then open boot look to rear of lamp in boot for either clip on panel or carpet covering lamp rear remove and look for some kind of nylon head screw bolt/s or 10 mm nuts? that my hold the lamp in place to body? or you may ?find the bulb/lamp board is simply a clip in to the lens assy as 1st example ? in that case just unclip and change bulb/s with no need to remove lens assy with a little patience you will succeed hope this helps

Nov 01, 2008 | 2006 Hyundai Elantra

Not finding what you are looking for?
2000 Hyundai Accent Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...