Check the fuel pump first.after that check the fuel filter. probably it is clogged.these parts are loacted in your fuel tank floater.remove the back seat.remove the screws.your car is young so the crankshaft position sensor must be working properly.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
P0316 FORD - Misfire Detected On Startup First 1000 Revolutions
- Engine Light ON (or Service Engine Soon Warning Light) - Engine fails to start - Engine runs rough
- Crankshaft Position (CKP) sensor harness is open or shorted - Crankshaft Position (CKP) sensor circuit poor electrical connection - Faulty Crankshaft Position (CKP) - Ignition System - Fuel Injectors - Running out of fuel - Fuel Quality
Dates Manufactured: JAN 2004
Number of Vehicles Affected: 653910
Date Owners Notified On: DEC 2007
CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT
POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL
OUTPUT FROM THE SENSOR.
Consequence of Defect: IF
THE INTERRUPTION IN THE SIGNAL FROM THE CRANKSHAFT POSITION SENSOR IS
SO BRIEF THAT THE ELECTRONIC CONTROL MODULE (ECM) LOGIC DOES NOT HAVE
TIME TO DIAGNOSE THE CONDITION, THE ENGINE MAY STOP RUNNING WITHOUT
WARNING WHILE THE VEHICLE IS DRIVEN AT A LOW SPEED INCREASING THE RISK
OF A CRASH.
Corrective Action: DEALERS
WILL REPROGRAM THE ECM FREE OF CHARGE. CERTAIN MY 2006 ALTIMAS WHICH
HAVE BEEN PREVIOUSLY REMEDIED UNDER RECALL CAMPAIGN 06V223 (NISSAN
R0606) ARE NOT INCLUDED IN THIS RECALL SINCE THE REPROGRAMMING FOR
06V223 ALSO INCLUDED THIS REPROGRAMMING. THE RECALL BEGAN ON DECEMBER
31, 2007. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
Electronic Engine ControlsWARNING To avoid personal injury and/or vehicle damage, refer to the service precautions at the beginning of this section. General Information
The Engine Management System (EMS) uses several different sensors and actuators to gather and control various emissions and driveability aspects of the vehicle. These may include but are not limited to:
MAP - Manifold Absolute Pressure Sensor
BARO - Barometric Pressure Sensor
FTP - Fuel Tank Pressure Sensor
ECT - Engine Coolant Temperature Sensor
A/F - Air Fuel Ratio Sensor
APP - Accelerator Pedal Position Sensor
CKP - Crankshaft Position Sensor
CMP - Camshaft Position Sensor
EGR Valve Position - Exhaust Gas Recirculation Valve Position Sensor
HO2S - Heated Oxygen Sensor
IAC - Idle Air Control Valve
IAT - Intake Air Temperature Sensor
KS - Knock Sensor
MAF - Mass Air Flow Sensor
TP - Throttle Position Sensor
Are there any codes that point to a problem with any of the above sensors?
The crankshaft position sensor (POS) is located on the oil pan facing the gear teeth (cogs) of the signal plate. It detects the fluctuation of the engine revolution. After replacement, ECM reprogramming is required. This vehicle may be subject to voluntary recall, CAMPAIGN I.D. # R0606, that involves the crankshaft position sensor:
Nissan has determined that on some 2003 - 2004 Altima and Sentra vehicles with the 2.5 liter engine the operation of the crank angle sensor is significantly affected by variations in temperature that occur due to the unique location of the sensor in the engine. Under certain driving conditions, these variations in temperature can be large enough to cause a brief interruption in the signal output from the sensor. If the interruption in the signal from the sensor is so brief that the Electronic Control Module (ECM) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at low speed.