Question about 1995 Toyota Celica

1 Answer

Installing replacement radiator

I have drained the system and detached the hoses. I cant tell if there are any transmission or engine oil lines to disconect, and I dont know how to unplug the fans (is there one plug ot two?) i guess what i am asking is in what order do I detach things.like (1)the electric plug(s) (2) the transmission oil cooler (if any on a manual transmission) Iand (3) the fans....'d like to get the unit out and do most of the detaching/attaching outside of the car.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 22,041 Answers

Manual or automatic ,with or without A/C

Posted on Jun 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace oil pan on a bmw 2004 330ci


Raise engine with special tool 00 0 200 approx. 5 mm.
- Remove suction filter housing. Remove engine splash guard.
- Drain engine oil. On vehicles with automatic transmission:
- Disconnect oil lines from automatic transmission and from oil pan.
- Release guide tube for dipstick.

Note: M52TU and M54 only.
- Detach return hose from cyclone oil separator on oil dipstick guide tube.
- Replace O-ring.
- Remove front end reinforcement.
- Detach steeling spindle from steering gear.
- Remove vane pump for power steering unit (lines remain connected).
- Disconnect plug connection to oil level sensor.
- Loosen top and unfasten bottom of left and right engine mounts.

E46 4WD only
- Remove left and right swivel bearings.
- Remove output shafts. Remove front propeller shaft.
- Remove front axle differential.
- Detach brackets for left and right control arms from engine carrier.
- Release retaining brackets for left and right stabilizer bars.
- Unfasten screw connection on front axle support and lower the front axle support.

Note: There is no need to detach the steering gear from the front axle support.

- Unfasten oil sump screws at transmission and engine ends.
- Lower and remove oil sump.
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agent to the area around seams.

Installation:
  1. Replace gasket
  2. Install oil sump.
  3. Insert all oil sump screws.
  4. Insert screws in transmission end without preload at this stage.
  5. Tighten down screws in engine end.
  6. Tighten down screws in transmission end.

E60 Removing And Installing, Sealing Or Replacing Oil Sump (M54)

Necessary preliminary tasks. -
- Remove intake filter housing
- Remove guide tube for oil dipstick
- Lowering front axle support
- Drain off engine oil
- Disconnect plug connection to oil level sensor.

On vehicles with automatic transmission:
- Detach oil lines from automatic transmission and from oil pan.
- Unfasten oil pan screws at transmission and engine ends.
- Lower and remove oil pan.

Installation:
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agen to the area around seams.

Installation:

  1. Replace seal.
  2. Install oil sump.
  3. Insert all screws on transmission end, without preload at this stage.
  1. Tighten down screws on engine end.
  2. Tighten screws on transmission end.

Or take it to a dealer....

Apr 19, 2011 | BMW 330 Cars & Trucks

2 Answers

How to remove radiator from my 2000 chrysler 300


Radiator Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect negative cable.
  3. Drain cooling system.
  4. Remove or disconnect the following:
    • Radiator upper crossmember
    • Upper and lower coolant hoses from the radiator
    • Transmission hoses from cooler
    • Engine oil cooler lines (if equipped)
    • Radiator fan electrical connector and fan assembly
    • Condenser mounting screws located at the front of the radiator
    • Transmission cooler line bracket from left side of radiator
  5. Lift condenser upward enough to disengage upper mounting clips. Allow condenser to rest on lower radiator crossmember.
  6. Lifted radiator from engine compartment.
To Install:
  1. Seat the radiator assembly lower rubber isolators into the mounting holes in radiator lower support.
  2. Attach air conditioning condenser to radiator
    • Torque to 45 inch lbs. (5 Nm)
  3. Install or connect the following:
    • Radiator lower hose
    • Transmission cooler line bracket and transmission hoses
      1. Torque to 28 inch lbs. (3 Nm)
    • Radiator fan and electrical connector
    • Engine oil cooler lines (if equipped)
      1. Torque to 160 inch lbs. (18 Nm)
    • Radiator upper hose
    • Radiator upper support crossmember
    • Negative cable
  4. Fill cooling system with coolant.
prev.gif next.gif

Aug 03, 2010 | 1999 Chrysler 300M

2 Answers

Radiator is leaking, on the drivers side of car. 2002 Chevy Avalanche, 4 wheel drive trcuk. One owner, 106000 miles on it.


Removal & Installation To Remove:
WARNING
To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is on or is still hot. The cooling system will release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot.
CAUTION
If the vehicle's coolant is low, drained out, or has repeatedly needed coolant or water added to the system, then the system should be completely flushed.
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Inlet hose from the radiator
    • Radiator outlet hose from the radiator
    • Lower fan shroud
    • Surge tank hose
    • Vent inlet hose from the radiator
    • Surge tank hose
    • Engine oil cooler lines from the radiator
    • Transmission oil cooler lines from the radiator Remove the radiator chevy_sub25_02-04_rad_rem.gif

    • Radiator bolts
    • Radiator from the vehicle
To Install:
  1. Install or connect the following:
    • Radiator to the vehicle
    • Radiator bolts and tighten the bolts, Torque to: 18 ft-lbs (25 Nm)
    • Engine oil cooler lines to the radiator
    • Transmission oil cooler lines to the radiator
    • Radiator vent inlet hose to the radiator
    • Lower fan shroud
    • Outlet hose to the radiator
    • Inlet hose to the radiator
  2. Fill the cooling system.
  3. Test drive the vehicle to confirm the repairs.
prev.gif next.gif

Jul 21, 2010 | 2002 Chevrolet Avalanche

1 Answer

How do you change the radiator on a 1996 Buick Skylark?


GM Grand Am/Achieva/Calais/Skylark/Somerset 1985-98 Radiator - REMOVAL & INSTALLATION
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
A cross-flow radiator is used on most models. The radiators used on automatic transaxle models are equipped with oil coolers with inlet and outlet fittings for transmission fluid circulation. An aluminum-plastic radiator can be identified by the black plastic side tanks and aluminum radiator.
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. If necessary for access to the radiator, remove the air intake duct assembly or air cleaner assembly.
  4. On automatic transaxles, disconnect and plug the upper oil cooler line.
  5. Disconnect the engine strut brace at the radiator, loosen the engine side bolt and swing aside, if equipped.
  6. Matchmark and remove the hood latch from the radiator support.
  7. Detach the upper hose and coolant reserve tank hose from the radiator.
  8. Disconnect the forward light harness and fan wiring. Remove the electric cooling fan. On some models this may not be able to be removed unless the front end of the vehicle is raised and supported.
  9. Raise and safely support the vehicle.
  10. Remove the engine cooling fan if not yet done.
  11. If equipped, remove the splash panel below the radiator outlet hose. Detach the lower hose from the radiator.
  12. If equipped, disconnect and plug the lower oil cooler line.
  13. Carefully lower the vehicle.
  14. If equipped with air conditioning, remove the radiator to condenser bolts. Unbolt the refrigerant line clamp. Do not disconnect the lines.
  15. Remove the mounting bolts and clamp, then the shroud (if equipped) and carefully lift the radiator out of the engine compartment.
To install:
  1. Lower the radiator into position.
  2. Install the mounting clamps and bolts, including those associated with air conditioning parts.
  3. Raise and safely support the vehicle.
  4. If equipped, attach the automatic transaxle cooler lines.
  5. Connect the lower hose(s) and attach the splash shield if equipped.
If the engine cooling fan was removed while the vehicle was in the air, install the assembly and attach all electrical wiring.
  1. Carefully lower the vehicle.
  2. If not already done, install the electric cooling fan, then attach the electrical connector(s).
  3. Connect the upper hose and coolant reserve tank hose.
  4. Install the hood latch and strut brace.
  5. Fill the system with coolant.
  6. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their correct levels, then check the automatic transaxle fluid level.
  7. Turn the engine OFF , then once the vehicle has cooled, recheck the coolant level.
Hopew this help (remember comment and rated this) TY for using Fixya.

May 05, 2010 | 1996 Buick Skylark

1 Answer

I need to find a guide to replacing the radiator in a 1997 Volvo S90 w/ automatic transmission.


Volvo 1990-1998 Repair Guide
Radiator - REMOVAL & INSTALLATION
Perform this work only on a cold engine.
  1. Disconnect the negative battery cable.
  2. Set the heater control to MAX heat.
  3. Remove the expansion tank cap.
  4. Place a suitable drain pan into position. Open the **** on the right-hand side of the engine block. Fit a hose to the **** to collect the coolant. Open the radiator draincock.
  5. Close the drain cocks when the coolant is completely drained.
  6. Remove the cooling fan.
  7. Remove the cooling fan shroud.
  8. Disconnect the upper and lower radiator hoses
  9. 91a8f77.jpg
  10. On vehicles equipped with automatic transmissions, disconnect the transmission oil cooler lines at the radiator. Plug the lines immediately. Catch the spillage from the radiator in a separate pan.
  11. 379639b.jpg
  12. Some vehicles are equipped with a temp sensor on the drivers side top of the radiator, if equipped remove the connector.
  13. Remove the radiator retaining bolts and brackets.
  14. a2b05c9.jpg _506019a.jpg
  15. Remove the radiator assembly from the vehicle.
  16. 45887bc.jpg

On 850/C70/S70/V70 models, the radiator comes out the bottom of the vehicle.
To install:
  1. Place the radiator into position and install the retaining bolts.
  2. On automatic transmission vehicles, connect the oil cooler lines.
  3. Install the fan and shroud.
  4. Install the lower and upper radiator hoses.
  5. Connect the expansion tank hose. Make sure that the overflow hose is clear of the fan and is free of any sharp bends.
  6. Fill the cooling system through the expansion tank, with a 50 percent antifreeze, 50 percent water solution.
  7. Connect the negative battery cable.
  8. Run the engine until normal operating temperature is reached.
  9. Bleed the cooling system.
  10. Check for leaks.
  11. Top up the cooling system, as required.
  12. Replace the cap.
  13. Check and top up the automatic transmission fluid level.

Hope thats help (remember comment and rated this).

Apr 29, 2010 | 1997 Volvo S90

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    1 Answer

    How do i change the radiator in a 2002 jaguar x type


    As detailed as I can :
    Drain the cooling system. Detach the air conditioning line .Raise the vehicle. Remove the lower radiator splash shield. The splash shield is equipped with hinges which should be treated with care on removal. Remove the radiator splash shield. Detach the securing clips. Remove the radiator splash shield. Seal the line and the evaporator with plugsDetach the air conditioning line. Detach the lower coolant hose. Remove the air conditioning condenser. Remove the securing screws. Vehicles with manual transmission, cable tie the cooling radiator. Detach the automatic transmission/power steering cooler. Remove the securing screws. Detach the automatic transmission/power steering cooler. Lower the vehicle. Remove the radiator foam trim. Remove the radiator. To install, reverse the removal procedure.

    Aug 11, 2009 | 2002 Jaguar X-Type

    2 Answers

    How do i replace a radiator


    1. Drain the engine coolant.
    2. On Canadian models, disconnect the relay block that controls the day time running lights.
    3. Detach the upper radiator hose.
    4. Remove the lower radiator hose from the water outlet pipe.
    5. On vehicles with an automatic transmission, remove the transmission oil cooler hoses from the cooler pipe.
    6. Detach the cooling fan connectors.
    7. Remove the Engine Coolant Temperature (ECT) switch connector.
    8. To remove the radiator cooling fans, detach the 2 bolts and 2 upper supports.
    9. Lift out the radiator and remove the radiator/cooling fans(s) assembly.
    10. Remove the lower supports.
    11. Remove the oil cooler hoses from the radiator.
    12. Remove the lower radiator hoses from the radiator if they are still attached.
    13. Remove the No.1 ECT switch.
    14. Detach the cooling fans from the radiator.
    Remember, SAFETY FIRST...never open, service, or drain radiator when hot. Serious burns or injury can occur. Always drain coolant into a sealable container. Cats and dogs are attracted to coolant and can be fatal to them if consumed. Coolant should be re-used unless it's contaminated or several years old.
    Sure hope this helps you and good luck.

    Jul 19, 2009 | 1998 Toyota Camry

    1 Answer

    Radiator replace


    I Hope you Find this Helpfull And Please Remember to RATE ME

    1. Drain the coolant.
    2. Disable the SIR.
    3. Move the forwarding discriminating sensor out of the way.
    4. Remove the air cleaner assembly.
    5. Remove the cooling fans.
    6. Disconnect the radiator inlet hose from the radiator.
      1. Disconnect the radiator outlet hose from the radiator.
      2. Disconnect the engine oil cooler lines from the right radiator end tank.
      3. Disconnect the transmission oil cooler lines from the left radiator end tank.
      4. Remove the left and the right engine torque struts.
        1. Remove the upper radiator support screws.
        2. Remove the radiator from the vehicle. Lift the radiator up and out. INSTALLATION PROCEDURE
          1. Install the radiator to the vehicle.
          2. Install the upper radiator support screws. Tighten the bolts to 6 Nm (53 inch lbs.). NOTICE: Refer to Fastener Notice in Service Precautions.
          3. Install the transmission oil cooler lines to the radiator. Tighten the transmission oil cooler line fittings to 27 Nm (20 ft. lbs.).
          4. Connect the engine oil cooler lines to the radiator. Tighten the engine oil cooler lines to 18 Nm (13 ft. lbs.).
          5. Install the left and the right engine support torque struts.Connect the radiator outlet hose to the radiator.
            1. Connect the radiator inlet hose to the radiator.
            2. Install the cooling fans.
            3. Install the air cleaner assembly.
            4. Install the forward discriminating sensor.
            5. Enable the SIR.
            6. Refill the coolant.
          6. Hope this Helps and PLEASE RATE ME

    Jun 03, 2009 | 1998 Cadillac DeVille

    Not finding what you are looking for?
    1995 Toyota Celica Logo

    109 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    70387 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6879 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...